S 735-080
(5) Do a test of the DFDR playback operation:
(a) Set the CMC to show octal label 101, SDI 00 from CMC port 20 in hexidecimal (C/20/101/00).
WARNING: MAKE SURE YOU HAVE PREPARED THE AIRPLANE FOR THE AIR MODE
_______ BEFORE YOU OPEN THE CIRCUIT BREAKER THAT FOLLOWS. AUTOMATIC OPERATION OF AIRPLANE SYSTEMS IN THE AIR MODE CAN CAUSE INJURY OR DAMAGE.
(b)
Open this circuit breaker:
1) P7, Overhead Circuit Breaker Panel
a) 7H8, GND SAFETY RLY
(c)
Make sure the Input Monitoring display (ARINC 429 bus-analyzer) is 62470082 (624700).
(d)
Close this circuit breaker:
1) P7, Overhead Circuit Breaker Panel
a) 7H8 GND SAFETY RLY
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
31-31-00
ALL ú ú 18 Page 509 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 735-081
(6) Do a test of the EIU data buses:
(a)
Set the CMC to show octal label 350, SDI 00 from CMC port 20 in binary (C/20/350/00).
(b)
Make sure that bits 15, 16, and 17 are set to a 0.
(c)
Open this circuit breaker:
1) P7, Overhead Circuit Breaker Panel
a) 7F09, EIU L
(d)
Make sure bit 17 changes to a 1.
(e)
Close this circuit breaker:
1) P7, Overhead Circuit Breaker Panel
a) 7F09, EIU L
(f)
Open this circuit breaker:
1) P7, Overhead Circuit Breaker Panel
a) 7F10, EIU C
(g)
Make sure bit 16 changes to a 1.
(h)
Close this circuit breaker:
1) P7, Overhead Circuit Breaker Panel
a) 7F10, EIU C
(i)
Open this circuit breaker:
1) P7, Overhead Circuit Breaker Panel
a) 7F15, EIU R
(j)
Make sure bit 15 changes to a 1.
(k)
Close this circuit breaker:
1) P7, Overhead Circuit Breaker Panel
a) 7F15, EIU R
S 735-082
(7) Do a test of the EICAS message signal:
(a) Set the CMC to show octal label 010, SDI 11 from the CMC port 26 in binary (C/26/010/11).
WARNING: MAKE SURE YOU HAVE PREPARED THE AIRPLANE FOR THE AIR MODE
_______ BEFORE YOU OPEN THE CIRCUIT BREAKER THAT FOLLOWS. THE AUTOMATIC OPERATION OF AIRPLANE SYSTEMS IN THE AIR MODE CAN CAUSE INJURY OR DAMAGE.
(b) Open this circuit breaker:
1) P7, Overhead Circuit Breaker Panel
a) 7H8, GND SAFETY RLY
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
31-31-00
ALL ú ú 16 Page 510 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(c)
Make sure that bit 28 is set to a 0.
(d)
Close this circuit breaker:
1) P7, Overhead Circuit Breaker Panel a) 7H8, GND SAFETY RLY
(e)
Make sure that bit 28 changes to a 1 after approximately 5 minutes.
S 735-083
(8) Do a test of the DFDR maintenance and status discretes:
(a)
Remove the Digital Flight Data Recorder (B579) from the E8 shelf (AMM 31-31-01/401).
(b)
Set the CMC to show octal label 270, SDI 00 from CMC port 20 in binary (C/20/270/00).
(c)
Do a test of the Maintenance discrete: 1) Make sure that bit 29 (MAINT) is set to a 0. 2) Ground pin 22 (MAINT) on the DFDR connector DB579CA in the
Aft Equipment Center, E8. 3) Make sure that bit 29 changes to a 1. 4) Remove the ground from pin 22.
(d)
Do a test of the Status discrete: 1) Make sure that bit 28 (STATUS) is set to a 0. 2) Ground pin 21 (STATUS) on the DFDR connector DB579CA. 3) Make sure that bit 28 changes to a 1. 4) Remove the ground from pin 21.
(e)
Install the flight data recorder (B579) on the E8 shelf (AMM 31-31-01/401).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 指示/記錄系統 1(54)
