S 014-046

 (5)  
Open the left fan cowl panel (Ref 71-11-04/201).

 S 014-047

 (6)  
Open the left core cowl panel (Ref 71-11-06/201).

 S 014-048
 WARNING: OBEY THE INSTRUCTIONS IN THE PROCEDURE TO OPEN THE THRUST
_______ REVERSERS. IF YOU DO NOT OBEY THE INSTRUCTIONS WHEN YOU OPEN THE THRUST REVERSERS, INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR.
 (7)  Open the left thrust reverser (Ref 78-31-00/201).
 S 864-006
 WARNING: YOU MUST RELEASE THE PRESSURE IN THE PNEUMATIC DUCT BEFORE
_______ YOU REMOVE A PNEUMATIC SYSTEM COMPONENT. THE HOT, HIGH PRESSURE AIR CAN CAUSE INJURIES TO PERSONS.
 (8)  
Do the steps that follow to release the pressure in the duct between the PRV and the HPSOV (Ref 36-11-05/201).

 (a)  
Turn the manual override drive on the HPSOV to the OPEN position momentarily.

 (b)  
Put the manual override drive to the CLOSED position.

 S 024-065
 (9)  
Do these steps to remove the P-Clamps:

 (a)  
Remove the nut and washer that hold the P-Clamp to the valve actuator.

 NOTE: Keep the nut and the washer for the installation.
____
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 36-11-19
 ALL  ú ú 03P Page 405 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (b)  Remove the P-Clamp and the spacers from the valve actuator.
 NOTE:____ Keep the P-Clamp on the wires for the installation.
 Keep the spacers for the installation.
 (c)  Remove and discard the lockwire from the bolt that holds the
 P-Clamp to the valve heat shield (AMM 20-11-28/401).
 (d)  Remove the bolt and the washer that hold the P-Clamp to the
 valve heat shield.
 NOTE:____ Valve PNs 790270-1 through -12 have a long bolt that
 goes through a spacer under the heat shield.  Hold the
 spacer while you remove the bolt to prevent dislocating
 the spacer.  Newer valves have a short bolt that screws
 into a threaded spacer under the heat shield.
 (e)  Remove the P-Clamp from the valve heat shield.
 NOTE:____ Keep the P-Clamp on the wires for the installation.
 (f)  Reinstall the washer and the bolt on the valve heat shield.

 S 034-007
 (10)
 Disconnect the wires from the PRV (1) terminal block.

 (a)  
Put a tag on the wires and the terminals to make the installation of the PRV easier.

 S 024-066
 (11) Remove the nut, the bolt, and the washers that hold the bonding jumper to the valve.
 NOTE: Keep the bolt, the nut and the washers for the installation.
____
 S 034-008
 (12)
 Disconnect the actuator pressure tube from the PRV (1).

 (a)  
Put the protective caps on the open tube and the port to keep out unwanted objects.

 S 034-039
 (13)
 Disconnect the couplings (7) upstream and downstream of the PRV (1).

 S 024-040

 (14)
 Remove the PRV (1).

 (a)  
If you cannot easily remove the PRV because it is too tight, loosen one of the duct sections on either side of the PRV (AMM 36-11-01/401).

 S 034-010
 (15)
 Remove the seals (8) from the duct flanges.

 (a)  
Examine the seals for damage.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 36-11-19
 ALL  ú ú 01P Page 406 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (b)  Replace the seals that have damage.
 S 034-011
 (16)
 Put the protective covers on the open ducts to keep out unwanted objects.

 S 034-012

 (17)
 Do the steps that follow if you must install a new PRV (1):

 (a)  
Remove the fittings from the PRV.

 (b)  
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊 氣動系統(tǒng) PNEUMATIC SYSTEM(119)