(3)  
AMM 24-22-00/201, Manual Control

 (4)  
AMM 36-00-00/201, Pneumatic System

 (5)  
AMM 36-11-04/201, Engine Bleed Air Pressure Regulating and Shutoff Valve (PRSOV)

 (6)  
AMM 71-11-04/201, Fan Cowl Panels

 (7)  
AMM 71-11-06/201, Core Cowl Panels

 (8)  
AMM 78-31-00/201, Thrust Reverser System

 C.
Access

 (1)  
Location Zone 412 Engine 1 - High Pressure Compressor Case 12:00 422 Engine 2 - High Pressure Compressor Case 12:00 432 Engine 3 - High Pressure Compressor Case 12:00 442 Engine 4 - High Pressure Compressor Case 12:00

 (2)  
Access Panel
 416 Right Thrust Reverser Half - Engine 1
 426 Right Thrust Reverser Half - Engine 2
 436 Right Thrust Reverser Half - Engine 3
 446 Right Thrust Reverser Half - Engine 4

 D.
Install the Fan Air Modulating Valve

 (1)  
Supply electrical power (AMM 24-22-00/201).

 S 864-010
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 36-12-04
 ALL  ú ú 01P Page 405 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (2)  S 644-039Apply anti-seize compound to the threads of the pneumatic connectors.
 (3)  S 434-011If you install a new valve, do the steps that follow: (a) Install the elbow (6), union (7), and O-ring (8) in the TEMP port. (b) Install an O-ring (5), elbow (3), and jamnut (4) in the SUPPLY and cooling air ports. (c) Install the flange plate (14) on the valve inlet. (d) Install the ground stud (20) on the valve ground strap (AMM 20-11-15/401).
 (4)  S 424-012Install the fan air modulating valve on the precooler flange. (a) Make sure the pin on the valve flange is engaged with the notch on the precooler flange.
 NOTE:____ The notch is at the 5:30 position.
 (b)  Tighten the coupling (2) to 110-125 pound-inches (12-14 N.m).
 (5)  S 434-013Connect the bonding jumper to the ground stud (20).
 (6)  S 764-014Make sure that the resistance between the ground stud (20) and the valve ground strap is less than 0.005 ohms (AMM 20-22-01/601).
 (7)  S 434-015Connect the tubes to their ports on the fan air modulating valve.
 (8)  S 434-016Connect the wires to the terminal block. (a) Remove the tags.
 (9)  S 864-017For the applicable engine, remove the DO-NOT-CLOSE tag and close this circuit breaker: (a) P6 Main Power Distribution Panel 1) 6H32 AIR SUPPLY CONT ENG 1 2) 6H33 AIR SUPPLY CONT ENG 2 3) 6H34 AIR SUPPLY CONT ENG 3 4) 6H35 AIR SUPPLY CONT ENG 4

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 36-12-04
 ALL  ú ú 01P Page 406 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 864-018
 (10)
 If there is an air-driven hydraulic pump (ADP) in operation on this wing, stop the operation of the ADP.

 (a)  
Do not continue to the subsequent step for ten minutes or until the pneumatic ducts on the wing are cool.

 S 794-019
 (11)
 Apply the leak detector to the tube connections for the TEMP and SUPPLY port for the fan air modulating valve.

 S 864-020

 (12)
 Pressurize the pneumatic system (AMM 36-00-00/201).

 S 984-021

 (13)
 Monitor the position of the fan air modulating valve.

 (a)  
Turn the manual override of the PRSOV to the OPEN position (AMM 36-11-04/201).

 NOTE: The manual override is on the left side of the strut.
____
 (b)  Make sure the fan air modulating valve goes to the CLOSED position.
 S 794-022
 (14)
 Examine the tube connections for the TEMP and SUPPLY ports.

 (a)  
Repair the tube connections if there is leakage.

 S 984-023
 (15)
 Put the PRSOV to the CLOSED position.

 S 864-024

 (16)
 Release the pressure in the pneumatic system (AMM 36-00-00/201).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 氣動系統 PNEUMATIC SYSTEM(151)