(2)
AIPC 36-11-04-03 or AIPC 36-11-04-04

 E.
Access

 (1)  
Location Zone
 452 Engine 1 - Strut Torque Box
 462 Engine 2 - Strut Torque Box
 472 Engine 3 - Strut Torque Box
 482 Engine 4 - Strut Torque Box

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 36-11-04
 ALL  ú ú 02 Page 303 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (2)  Access Panel
 452FL Access Door, Mid Lower Strut Aft - Engine 1
 462FL Access Door, Mid Lower Strut Aft - Engine 2
 472FL Access Door, Mid Lower Strut Aft - Engine 3
 482FL Access Door, Mid Lower Strut Aft - Engine 4

 F. Procedure
 S 013-018
 (1)  
Remove the access door from the applicable engine strut
 (AMM 54-62-00/201).

 S 023-004

 (2)  
Remove the threaded plug (1, 2), preformed packing (3, 4), spring (5, 6), and air filter (7, 8) from the valve ports G1 and G2.

 (a)  
Remove the preformed packing (3, 4) from the threaded plug (1, 2) and discard the preformed packing (3, 4).

 S 113-019
 (3)  
Replace the air filter (7) with a new air filter (7), or clean the air filter (7) per the Hamilton Standard CMM 36-11-12.

 S 113-020

 (4)  
Replace the air filter (8) with a new air filter (8), or do these steps to clean the air filter (8):

 (a)  
Blow clean, dry, filtered air (at less than 25 psi) into the air filter (8) to remove the particles which have collected in the air filter mesh.

 (b)  
Make sure that the filter flange is flat, and that the air filter mesh is not damaged. 1) Replace the air filter (8), if it is damaged.

 (c)  
Clean the air filter (8) with solvent, if it is dirty.

 NOTE: Fingerprints will contaminate the filter.
____
 (d)  Blow clean, dry, filtered air (at less than 25 psi) into the air filter (8) to fully dry the filter.
 S 423-010
 (5)  Install the air filter (7, 8) into the valve ports G1 and G2.
 NOTE: The flanged end of the filter must be against the valve port.
____ The valve port G1 is for the air filter (7).
 S 423-011
 (6)  
Install the spring (5, 6) in the valve ports G1 and G2.

 S 423-021

 (7)  
Apply the lubricant, DC44, to a new preformed packing (3, 4), then install the preformed packing (3, 4) to the threaded plug (1, 2).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 36-11-04
 ALL  ú ú 04 Page 304 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (8)  S 423-012Apply the thread lubricant, Mo-Lith No. 2, to the threads of the threaded plug (1, 2), then install the threaded plug (1, 2) in the valve ports G1 and G2.
 (9)  S 423-013Tighten each threaded plug (1, 2) to 60-70 pound-inches (6.8-8.0 N.m), and install lockwire.
 S 213-014

 CAUTION: TOOLS, LOOSE MATERIAL, AND DEBRIS IN STRUT CAVITIES MAY BLOCK
_______ STRUT DRAINS, AND CAUSE THE DRAIN SYSTEM TO BE INEFFECTIVE.
 (10)
 Make sure that all tools and loose material are removed, and the strut cavities are free of debris before you install the access door.

 S 413-016

 (11)
 Install the access door on the applicable engine strut (AMM 54-62-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 36-11-04
 ALL  ú ú 03 Page 305 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 ENGINE BLEED AIR PRESSURE REGULATING AND SHUTOFF VALVE (PRSOV) -
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 氣動系統 PNEUMATIC SYSTEM(82)