(d)  Put a sheet of lead-coated fabric between the layers of the
 blanket if it is necessary.
 NOTE: The lead-coated fabric must have 0.25-inch diameter____
 holes. If the insulation blanket width is less than 12
 inches,there must be one hole for each 10-inch length of
 the blanket. If the blanket width is more than 12
 inches, there must be two holes for each 10-inch length
 of the blanket.
 (e)  Cut the fabric covering and lead-coated fabric, if it is
 necessary.
 (f)  Use a staple to connect the layers of the blanket to ease
 handling during stiching, taping or heat sealing of blankets.
 NOTE: The staples must be between the stitches and the____
 outer edge of the blanket. The staples must not show on
 the completed blanket. Make sure the staples go through
 the inboard and outboard covering and the fiberglass
 insulation only.
 (g)  Stitch the blanket edges with between four and six stitches for
 each inch of blanket edge.
 (h)  Close the edges and the cutouts of the blanket with fabric
 strips, with the steps that follow:
 1) On edges with flaps, make the flaps the same width as the
 damaged blanket.
 2) On edges that have the same thickness for the whole
 blanket, use cement to attach the nylon binding.
 3) On edges with a binding that is sewn, use 4-cord cotton
 thread with between four and six stitches for each inch.
 4) Install nylon fabric grommets through the holes in the
 blanket.
 5) Bond the grommets to the blanket with BMS 5-30 cement.
 (i)  On ceiling panels, seal the stitching on the outboard side of
 the blanket with a continuous bead of BMS 5-30 cement.
 NOTE: You can make the cement thin with MEK if it is____
 necessary.

 TASK 25-00-00-308-194
 10. Repair Aluminum Trim
____________________
 A. General
 (1) This procedure gives instructions to repair aluminum trim.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 25-00-00
 ALL  ú ú 01 Page 838 ú Jan 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

 WARNING:_______DO NOT BREATH THE ASBESTOS DUST. PUT ON A PROTECTIVE RESPIRATOR WHEN YOU DRILL THE LAVATORY PANELS. THE ASBESTOS DUST CAN GET IN YOUR MOUTH OR NOSE IF YOU DO NOT USE THE PROTECTIVE RESPIRATOR AND CAN CAUSE CANCER OR LUNG DISEASE.
 (2)  Obey this WARNING during all of this task.
 B. Equipment
 (1)  Heat Gun - 1200 to 1500 watts
 C. Consumable Materials
 (1)  
Adhesives

 (a)  
Adhesive - BMS5-123, Hysol 608

 (b)  
D00147 Filler - BMS 5-136, Ad Tech 15-3

 (c)  
A00028 - Adhesive BMS5-92, 3M 2216

 (2)  
B00168 Paper - Abrasive, 400-600 grit

 D. References
 (1) AMM 20-10-26/201, Heat Guns, Soldering Guns, and/or Soldering Irons
 E. Access
 (1)  Location Zone
 200 Upper Half of the Fuselage

 F. Repair Aluminum Trim
 S 018-195
 (1)
Remove any fasteners from the aluminum trim if they are installed.

 S 018-196

 (2)  
Remove the aluminum trim from the panel.

 S 018-197

 (3)
If the trim is bonded, use a heat gun to help remove the trim.

 (a)
Apply heat while pulling the trim away from the panel.

 (b)  
Remove the trim progressively from one end to the other.

 S 828-198
 (4)  Restore the trim to its original straightness and contour.
 NOTE: Use metal working techniques to remove dents and straighten
____
 the trim as much as possible.

 S 418-199
 (5)  
Put the trim onto the panel and reattach any fasteners.

 S 418-200

 (6)  
If the trim is applied with fasteners and adhesive, apply epoxy adhesive to the edge of the panel and quickly reattach the trim with the fasteners.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 EQUIPMENT/FURNISHINGS 1(29)