25-66-01
 ALL  ú ú 04 Page 409 ú May 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
 CAUTION:_______DO NOT TURN THE ALLEN WRENCH CLOCKWISE. IF YOU TURN THE ALLEN WRENCH CLOCKWISE, YOU CAN ACCIDENTALLY INFLATE THE SLIDE. THIS CAN CAUSE DAMAGE OR INJURY.
 (b)  
Carefully turn the allen wrench counterclockwise a small distance to align the detent pin on the lock pin housing with the stop mark on the valve coverplate (Fig. 404).

 (c)  
Fully install the safety pin.

 F. Remove Escape Slide (Fig. 402)
 S 824-010
 (1)  Move the mode selector lever to the ENGAGE position.
 S 824-013
 CAUTION: DO NOT TURN THE INTERIOR HANDLE TO THE FULLY UNLATCHED POSITION
_______ WHILE THE DOOR IS IN THE ENGAGE MODE. THIS WILL OPERATE THE EMERGENCY POWER SYSTEM, WHICH CAN CAUSE INJURY OR DAMAGE.
 (2)  
Turn the interior handle slowly toward the unlatched position (approximately 30 degrees), until the cams on girt bar slider cranks lift sufficiently to clear the bar locks (4).

 S 824-016

 (3)  
Push the leaf spring down and move the bar locks (4) toward the middle of the girt bar (3).

 S 034-017

 (4)  
Lift the girt bar (3) out of the floor fittings.

 S 034-113

 (5)  
Lightly wrap the leaf springs and girt bar with tape.

 NOTE: This will help prevent damage to the leaf springs.
____
 S 824-018
 (6)  
Turn the interior handle back to the latched position.

 (7)  
Move the mode selector lever to the DETACH position.

 S 034-022

 (8)  
If you install a new slide pack (1), do these steps:

 (a)  
Remove the bar lock (4).

 (b)  
Remove the girt bar (3) (Ref 25-66-10).

 (c)  
Put the bar locks (4) on the ends of the girt bar (3).

 (d)  
Attach the girt bar (3) to the floor fittings.

 S 824-019
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 25-66-01
 ALL  ú ú 09 Page 410 ú May 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL

INTERIOR HANDLE
INFLATION CYLINDER
PRESSURE REGULATOR INFLATION CYLINDER
SEE PULLEY HOUSING

ALLEN WRENCH
PRESSURE GAGE

A 
B
Safety Lockpin Installation Figure 404
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 25-66-01
 ALL  ú ú 01 Page 411 ú May 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
 S 034-025
 (9)
Hold up the slide pack (1), and release the harness buckles.

 S 034-028

 (10)
 Hold up the slide pack (1), and unhook the harness from the upper attach points.

 S 824-031

 (11)
 Lower the slide pack (1) to the floor with the harness.

 S 034-034

 (12)
 Release the lower harness latch at the lower shelf.

 S 024-035

 (13)
 Hold the girt against the slide pack (1), and remove the slide pack (1).

 S 434-038

 (14)
 If you do not install the slide pack (1) soon after you remove it, attach the lower shelf in the up position, and attach the harness to the upper attach points.

 S 024-108

 (15)
 If you install a new slide pack (1), remove the release strap/latch cable or chain fastener, the harness latch, and the cable or chain assembly from the pack (1) that you remove.

 TASK 25-66-01-404-044
 3.  Install Escape Slide (Fig. 402)____________________
 A. General
 (1)  In this task an escape slide or slide-raft is referred to as an escape slide.
 B. Equipment
 (1)  Safety Pin Set - Passenger Door Emergency Power
 Reservoir, B52009-1

 NOTE: The safety pin set is a set of 2 pins
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 EQUIPMENT/FURNISHINGS 2(78)