(2) Safety Pin Set - Passenger Door Emergency Power
Reservoir, B52009-1
NOTE: The safety pin set is a set of two pins
____ connected by a lanyard. If the safety pin set is not available, you can use two bolts (3/16-inch diameter by 1 1/4-inch grip) as an alternative. Install one bolt above and one bolt below the reservoir plunger. Attach tags to the bolts to identify the bolts for removal.
C. References
(1) 25-66-01/401, No. 1, 2, and 4 Passenger Door Escape Slides.
D. Access
(1) Location Zones
831 No. 1 Passenger Door (Left)
832 No. 2 Passenger Door (Left)
836 No. 4 Passenger Door (Left)
841 No. 1 Passenger Door (Right)
842 No. 2 Passenger Door (Right)
846 No. 4 Passenger Door (Right)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
25-66-10
ALL ú ú 01 Page 201 ú Dec 20/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL
MODE SELECTOR LEVER
INTERIOR HANDLE
PRESSURE GAGE
2. ESCAPE SLIDE-RAFT
AND REGULATOR
INFLATION CYLINDER GIRT
GIRT BAR
SEE A
NO. 1, 2, OR 4 PASSENGER DOOR (COVER NOT SHOWN)
1. GIRT BAR
PUSHRODS
CAM FLOOR FITTING
GIRT BAR
(2 LOCATIONS) LEAF SPRINGA SEE B
PROXIMITY SWITCH
0.45 |0.04 INCH
1. GIRT BAR PROXIMITY SWITCH A-A TARGET
FLOOR FITTING
LEAF SPRING
GIRT BAR SLIDER A
1. GIRT BAR
A
FLOOR FITTING
(EXAMPLE)
B
Girt Bar and Floor Fittings
Figure 201
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
25-66-10
ALL ú ú 03 Page 202 ú Dec 20/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL
Girt Bar Installation
Figure 202
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
25-66-10
ALL ú ú 01 Page 203 ú Jun 20/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL
EMERGENCY POWER RESERVOIR
Emergency Power Reservoir Safety Pin
Figure 203
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
25-66-10
ALL ú ú 01 Page 204 ú Jun 20/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
E. Procedure
S 012-002
(1)
Remove the cover for the escape slide (2) (Ref 25-66-01).
S 032-005
(2)
Remove the safety pin from the stowage pouch on the escape slide (2).
S 492-009
(3)
Install the safety pin into the inflation cylinder regulator.
S 822-001
(4)
If you cannot fully install the safety pin in the lock pin housing on the valve assembly do these steps:
(a) Install an allen wrench in the center of the pulley housing.
NOTE: You can use an allen wrench with a long handle for
____
easier access.
(b)
Carefully turn the allen wrench counterclockwise a small distance to align the detent pin on the lock pin housing with the stop mark on the valve coverplate.
(c)
Fully install the safety pin.
S 012-011
(5) Remove the escape slide (2) (Ref 25-66-01).
S 032-014
CAUTION: BE CAREFUL NOT TO PULL ON THE GIRT WHEN YOU REMOVE THE GIRT BAR
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 EQUIPMENT/FURNISHINGS 2(86)
