S 864-009

 (4)  
Open these circuit breakers on the overhead panel, P11, and attach DO-NOT-CLOSE tags:

 (a)  
11H17, FLT CONT SHUTOFF TAIL LEFT

 (b)  
11H18, FLT CONT SHUTOFF TAIL CTR

 (c)  
11H28, FLT CONT SHUTOFF TAIL RIGHT

 (5)  
Open access door 113AL (Ref 06-41-00).

 S 014-010
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-03
 ALL  ú ú 01 Page 401 ú Mar 20/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL

CRANK ASSEMBLY 
RUDDER  SEE  A 
PEDAL 
ADJUSTMENT 
CABLE  RUDDER FORWARD 
SEE  C  QUADRANT 
HOUSING ASSEMBLY  STOP PLATE 
CABLE RETAINING 
SLEEVE  WASHER  RIG PIN HOLE 
WASHER  R1A (LEFT) 
CABLE  WASHER  R1B (RIGHT) 
JACKSHAFT 
NUT  ASSEMBLY  RIG PIN 
SEE  B  HOLE R2 

FWD
BOLT WASHER NUT
CABLE CLAMPS (4 LOCATIONS)
(7 LOCATIONS) CRANK LEVER ASSEMBLY
CRANK ASSEMBLY
A
RUDDER PEDAL HOUSING
SEE DRUDDER PEDAL ADJUSTMENT CABLE
WASHER
SLEEVE FWD
RUDDER PEDAL
RUDDER
ADJUSTMENT CABLE
JACKSHAFT CABLE
C
RETAINING SIDE PANEL
NUT (2 LOCATIONS)
SCREWS (24 LOCATIONS)
FWD
JACKSHAFT ASSEMBLY
B
 FWD
RUDDER PEDAL HOUSING
D
Rudder Pedal Adjustment Crank Installation
Figure 401

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-03
 ALL  ú ú 01 Page 402 ú Mar 20/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

 E. Remove Rudder Pedal Adjustment Crank (Fig. 401)
 S 494-011
 (1)  
Install these rig pins:

 (a)  
R1A and R1B (in the applicable rudder pedal arms through the rudder pedal housing).

 (b)  
R2 (for the forward quadrant)

 S 034-001
 (2)  
Do these steps to disconnect the bottom of the cable:

 (a)  
Loosen the cable retaining nut at the forward quadrant.

 (b)  
Remove the cable clamps (7 locations) and the grommet.

 (c)  
Hold the cable retaining nut and washer, then pull the cable from the jackshaft and through the grommet hole.

 NOTE: Get access to the cable housing and the crank lever
____ assembly through the rudder pedal covers.
 S 034-002
 (3)  
Do these steps to disconnect the top of the cable:

 (a)  
Remove the nut and washer from the crank lever assembly. Remove the crank lever assembly. Remove the washer.

 (b)  
Remove the cable retaining sleeve at the crank housing and move it to the center of the cable.

 (c)  
Pull the cable from the crank housing and remove it.

 S 034-013
 (4)
Remove the four bolts, washers and nuts from the stop plate.

 S 034-014

 (5)  
Remove the stop plate and the crank housing.

 TASK 27-21-03-424-015
 3. Install Rudder Pedal Adjustment Crank
_____________________________________
 A. Equipment
 (1)  
Alignment Tool and Wrenches, Rudder Pedal
 Adjustment (from Torque Equipment - Rudder
 Pedal Adjustment, B27064-1 or -2)

 (a)  
Alignment Tool - B27064-5 (Supplied with Torque Equipment B27064-1 and -2)

 (b)  
Flare Nut Wrench - FRH 280 (SNAP-ON TOOLS, Kenosha, Wisconsin)

 NOTE:____Commercially Available. Supplied with the Torque Equipment B27064-1 only.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-03
 ALL  ú ú 01 Page 403 ú Mar 20/90
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(39)