曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

2  BUSHING BOLT OD ID  0.5000 (12.700) 0.5005 (12.713) 0.4985 (12.662) 0.4995 (12.687)  0.5025 (12.764) 0.4975 (12.637)  0.0030 (0.076)  X X 
3  BUSHING BUSHING ID OD  0.6870 (17.450) 0.6877 (17.468) 0.6860 (17.424) 0.6865 (17.437)  0.6890 (17.501) 0.6852 (17.404)  0.0025 (0.064)  X X 
4  BUSHING BOLT ID OD  0.6245 (15.862) 0.6252 (15.880) 0.6230 (15.824) 0.6240 (15.850)  0.6273 (15.933) (15.796) 0.6219  0.0032 (0.081)  X X 
5  BUSHING BOLT ID OD  0.6245 (15.862) 0.6252 (15.880) 0.6230 (15.824) 0.6240 (15.850)  0.6270 (15.926) 0.6220 (15.799)  0.0030 (0.076)  X X 
6  BUSHING BUSHING ID OD  0.8745 (22.212) 0.8753 (22.233) 0.8735 (22.187) 0.8740 (22.200)  0.8767 (22.268) 0.8726 (22.164)  0.0027 (0.069)  X X 
7  BUSHING BUSHING ID OD  0.8745 (22.212) 0.8753 (22.233) 0.8735 (22.187) 0.8740 (22.200)  0.8767 (22.268) 0.8726 (22.164)  0.0027 (0.069)  X X 
8  BUSHING BOLT ID OD  0.6245 (15.862) 0.6250 (15.875) 0.6230 (15.824) 0.6240 (15.850)  0.6270 (15.926) 0.6220 (15.799)  0.0030 (0.076)  X X 
9  BUSHING BOLT OD ID  0.6245 (15.862) 0.6252 (15.880) 0.6230 (15.824) 0.6240 (15.850)  0.6273 (15.933) 0.6219 (15.796)  0.0032 (0.081)  X X 
10  SPACER BOLT OD ID  0.6245 (15.862) 0.6250 (15.875) 0.6230 (15.824) 0.6240 (15.850)  0.6270 (15.926) 0.6220 (15.799)  0.0030 (0.076)  X X 

Rudder Wear Limits
Figure 601 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-21
 ALL  ú ú 01 Page 603 ú Jan 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL

INDEX NO. 11  PART NAME DIM. BUSHING BUSHING ID OD  (mm) DESIGN LIMITS DIAMETER INCHES MINIMUM (mm) MAXIMUM INCHES 0.8735 (22.187) (22.200) 0.8740 0.8745 (22.212) (22.233) 0.8753  (mm) PERMITTED DIMENSION INCHES WEAR WEAR LIMITS (22.164) 0.8726 (22.268) 0.8767  (mm) MAXIMUM DIAMETER CLEARANCE INCHES (0.069) 0.0027  PART WORN REPLACE X X  PART WORN REPAIR REPAIR INSTR 
12  BOLT BUSHING OD ID  0.6230 (15.824) 0.6240 (15.850) 0.6245 (15.862) 0.6250 (15.875)  0.6220 (15.799) 0.6270 (15.926)  (0.076) 0.0030  X X 
13  BUSHING BUSHING ID OD  0.8735 (22.187) 0.8740 (22.200) 0.8745 (22.212) 0.8753 (22.233)  0.8727 (22.167) (22.268) 0.8767  (0.069) 0.0027  X X 
14  BOLT BUSHING ID OD  (15.824) 0.6230 (15.850) 0.6240 0.6245 (15.862) 0.6252 (15.880)  (15.799) 0.6220 0.6272 (15.931)  (0.081) 0.0032  X X 

Rudder Wear Limits
Figure 601 (Sheet 3)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-21
 ALL  ú ú 01 Page 604 ú Jan 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
M38748
A

757 MAINTENANCE MANUAL
 AILERON AND RUDDER TRIM CONTROL MODULE -
________________________________________ MAINTENANCE PRACTICES
_____________________
 1.  General_______
 A.  This procedure contains the removal and installation tasks for the trim control module for the ailerons and the rudder. There are tasks to remove and install the rudder trim indicator from the trim module. There is also a procedure to clean the rudder trim knob and its lightplate.
 TASK 27-21-23-022-001
 2.  Aileron and Rudder Trim Control Module - Removal________________________________________________
 A.  References
 (1)  
24-22-00/201, Electrical Power - Control

 B.  
Access

 (1)  
Location Zones
 211/212 Control Cabin

 C.  
Prepare for the Removal

 S 862-002
 (1)  
Supply electrical power (Ref 24-22-00).

 S 862-003

 (2)  
Move the FLT CONTROL SHUTOFF switches L, R, and C on the right side panel, P61, to OFF. Attach DO-NOT-OPERATE tags and make sure the switch position lights come on.

 S 862-004

 (3)  
Open these circuit breakers on the overhead panel, P11, and attach DO-NOT-CLOSE tags:

　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(92)