F.
Access

 (1)  
Location Zones
 211 Control Cabin (Left)
 324 Vertical Stabilizer - Rear Spar to Trailing Edge

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-13
 ALL  ú ú 01 Page 208 ú May 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

 (2)  
Access Panels
 324AL Body to Fin Seal
 324BL Aft Side of Rear Spar and Rudder Hinge

 G.
Rudder Ratio Changer Actuator (RRCA) - Installation (Fig. 201)

 S 422-033
 (1)  
Do these steps to connect the RRCA (37) to its support (13):

 (a)  
Put the RRCA (37) in its correct position. Make sure the anti-rotation clevis (14) is engaged.

 (b)  
Install and tighten the bolt (11), washer (38), and nut (12).

 S 422-034
 (2)  
Do this step to connect the RRCA (37) to the left ratio changer crank (9).

 (a)  
Install and tighten the bolt (2), bushing (3), washer (4), and nut (5).

 S 432-089
 (3)  
Connect these components to the RRCA:

 (a)  
the electrical connectors (26, 33)

 (b)  
the hydraulic hoses (15, 18, 19).

 S 822-080
 (4)  
Do the Rudder Ratio Changer Actuator - Oscillation Check
 (AMM 27-21-00/501).

 S 862-099

 (5)  
Make sure rig pins R5 and R6 can be easily installed and removed at the same time. If you cannot easily install and remove rig pins R5 and R6, do the adjustment procedure for the rudder ratio changer mechanism (AMM 27-21-00/501).

 S 422-100

 (6)  
If the RRCA support clevis was removed at the time of RRCA removal, do the RRCA Adjustment (AMM 27-21-00/501).

 NOTE: The rudder ratio changer and the rudder system rigging
____ are very sensitive to the shimming of the RRCA support clevis. If the clevis was removed to make the removal of the RRCM easier, the clevis must be installed (AMM 27-21-12/201). This can require the adjustment of the RRCA support clevis shims and system rigging (AMM 27-21-00/501).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-13
 ALL  ú ú 01 Page 209 ú May 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

 S 822-106
 (7)  
If the RRCA support clevis was not removed at the time of the RRCA removal, do the Rudder Ratio Changer System - Test (AMM 27-21-00/501).

 H.
RRCA Filter - Installation (Fig. 201)

 S 642-091
 (1)  
Put hydraulic fluid on all of the seals, packing, and backup rings before installation.

 S 032-092

 (2)  
Install these components:

 (a)  
the packing (28) and the backup rings (27) on the filter (29)

 (b)  
the filter (29) in the RRCA

 (c)  
the packing (32) and the backup rings (30) on the cap (31).

 S 392-093
 (3)  
Apply the sealant to the cap threads.

 S 432-053

 (4)  
Install the cap (31) on the RRCA and torque it to 350 - 375 pound-inches.

 S 432-054

 (5)  
Lock the cap (31) with wire.

 I.
RRCA Screen - Installation (Fig. 201)

 S 642-094
 (1)  
Put hydraulic fluid on all of the seals and the packing (16) before installation.

 S 432-095

 (2)  
Install these components:

 (a)  
the screen (20) in the RRCA

 (b)  
the packing (16) on the union (17).

 S 432-058
 (3)  
Install the union (17) on the RRCA and torque it to 110 - 120 pound-inches.

 S 432-059

 (4)  
Lock the union with wire.

 J.
RRCA Solenoid Valve - Installation (Fig. 201)

 S 642-096
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(66)