-
Remove the Feel, Centering, and Trim mechanism from the Aft Quadrant Assembly
-
Remove the Rudder Trim Actuator
-
Remove the Roller Bearing from the Cam Roller Arm Assembly
Because this task contains four procedures, only the applicable group of steps must be done.
To start one of these procedures, do the "Prepare for Removal" group of steps. Then, do the group of steps that is necessary to remove the component.
B. Equipment
(1)
Nose Gear Towing Lever Lockpin - A09003-1
C.
References
(1)
06-42-00/201, Empennage Access Doors and Panels
(2)
24-22-00/201, Electrical Power - Control
(3)
27-00-01/201, Flight Control Cables
D.
Access
(1)
Location Zones 311 Area Aft of Pressure Bulkhead to BS 1787.45 (Left) 324 Vertical Stabilizer - Rear Spar to Trailing Edge
(2)
Access Panels
311AL Control Cables
324AL Body to Fin Seal
324CL Rudder Hinge and PCAs
E.
Prepare for Removal
(1)
Supply electrical power (Ref 24-22-00).
S 862-003
(2)
Move the FLT CONTROL SHUTOFF switches L, C, and R on the right side panel, P61, to OFF. Attach DO-NOT-OPERATE tags and make sure the switch position lights come ON.
S 862-002
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-21-06
ALL ú ú 01 Page 201 ú Mar 20/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL
AFT QUADRANT, FEEL,
CENTERING, AND TRIM
INSTALLATION
SEE A
BOLT
BUSHING
WASHER
NUT
CABLE RA
RIG PIN HOLE R3
BOLT ASSEMBLY SEE C CABLE RB AFT QUADRANT
CONTROL RODS TO RATIO CHANGER
BOLT BUSHING WASHER NUT
CONNECTION POINT
B
RUDDER TRIM ACTUATOR
SEE E
CONNECTION POINT
SEE B
TORQUE TUBE
BOLT ASSEMBLY
SEE D
BOLT BUSHING WASHER NUT (3 LOCATIONS)
CONTROL ROD FROM AUTOPILOT (3 LOCATIONS)
FEEL, CENTERING AND TRIM MECHANISM
AFT QUADRANT, FEEL, CENTERING, AND TRIM INSTALLATION
A
Aft Quadrant Assembly
Figure 201 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-21-06
ALL ú ú 01 Page 202 ú Jun 20/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL
TORQUE TUBE
BOLT BUSHING
ASSEMBLY OUTER NUT
BOLT ASSEMBLY
SEE F
WASHER INNER NUT
SUPPORT BRACKET
BOLT ASSEMBLY
C
TORQUE TUBE
BOLT ASSEMBLY OUTER NUT BOLT
ASSEMBLY SEE G
INNER NUT
BUSHING WASHER
SUPPORT BRACKET RUDDER TRIM ACTUATOR BOLT ASSEMBLY
E D RUDDER TRIM ACTUATOR
RUDDER TRIM ACTUATOR
WASHER INNER NUT INNER NUT
BOLT ASSEMBLY
BOLT
OUTER NUT ASSEMBLY OUTER NUTSUPPORT BRACKET
SPRING ARM ASSEMBLYBUSHINGSUPPORT BRACKET
BOLT ASSEMBLY BOLT ASSEMBLY
GF
Aft Quadrant Assembly Figure 201 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-21-06
ALL ú ú 01 Page 203 ú Jun 20/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(46)
