(6)
ON THE CAPTAIN'S JACKSHAFT;
remove the control rod from the interconnect crank.
S 034-016
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-21-05
ALL ú ú 02 Page 406 ú Dec 20/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL
(7) S 034-057ON GUN 102-999; disconnect the control rod from the crank arm on the first officer's jackshaft.
(8) S 034-019Remove the wire bundles and the clamps.
(9) S 034-020Remove the interconnect crank that is located below the captain's jackshaft. Put the nuts back on the bolts to keep the bolts out of the jackshaft.
S 034-062
(10)
ON GUN 102-999; remove the crank arm that is located below the first officer's jackshaft. Put the nuts back on the bolts to keep the bolts out of the jackshaft.
S 034-022
(11)
Remove the rudder pedal housing cover that is opposite the jackshaft. Do the steps that follow:
(a)
ON GUN 102-999; disconnect the electrical connector from the transducer that is located below the first officer's jackshaft.
(b)
Remove the wire bundles.
(c)
Remove the bolts from the top front and sides of the cover (16 locations).
(d)
Remove the bolts from the face and bottom sides of the cover (41 locations).
(e)
Remove the rudder pedal pushrods from the rudder pedal arms.
S 034-023
(12) Hold the jackshaft and remove the jackshaft housing from the flight deck floor. Disengage the jackshaft from the top bearing housing.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-21-05
ALL ú ú 03 Page 407 ú Dec 20/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
S 034-024
(13)
Remove the aft panel from the jackshaft housing.
S 034-025
(14)
Lift the jackshaft from the bottom bearing housing, then pull the jackshaft and rudder pedal pushrods from the jackshaft housing.
S 034-026
(15)
Remove the rudder pedal pushrods from the jackshaft yokes.
S 034-027
(16)
Remove the top and bottom bearing housings.
TASK 27-21-05-424-028
3. Install Rudder Jackshaft and Forward Quadrant_____________________________________________
A. Equipment
(1)
Rig Pins from Set B20003-XX (Ref 20-10-24):
(a)
R1A - P/N B20003-26
(b)
R1B - P/N B20003-26
(c)
R2 - P/N B20003-22
(d)
R3 - P/N B20003-16
(2)
Alignment tool and wrenches, Rudder Pedal
Adjustment (from Torque Equipment - Rudder
Pedal Adjustment B27064-1 or -2)
(a)
Alignment Tool - B27064-5
(part of B27064 -1 and -2)
(b)
Flare Nut Wrench - SNAP-ON TOOLS - FRH 280, Snap-On-Tools, Kenosha, Wisconsin
NOTE: Supplied with equipment B27064-1
____
(c) Crowfoot Wrench - Utica - AC34, Utica Tool Company, Orangeburg, South Carolina
NOTE: Supplied with equipment B27064-1
____
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-21-05
ALL ú ú 04 Page 408 ú Jan 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL
B. Consumable Materials
(1)
D00013 Grease, MIL-G-23827
C.
References
(1)
06-41-00/201, Fuselage Access Doors and Panels
(2)
06-42-00/201, Empennage Access Doors and Panels
(3)
24-22-00/201, Electrical Power - Control
