S 014-005
(4)
Open the access door for the neutral shift and override mechanism, 313AL (Ref 06-42-00).
S 864-006
(5)
Move the horizontal stabilizer until Dimension B on the stabilizer ballscrew actuator is 15.89 | 0.01 inches
(403.6 +/- 0.25 mm) (Fig. 401).
S 864-007
(6)
Remove the pressure from the right and center hydraulic systems (Ref 29-11-00).
S 864-008
(7)
Put the L, R, and C FLT CONTROL SHUTOFF switches on the right side panel, P61, to the OFF position.
S 864-009
(8)
Put the RIGHT and CENTER STAB TRIM SHUTOFF valve switches on the control stand panel, P10, to the CUTOUT position.
S 864-010
(9)
Open these circuit breakers on the overhead panel, P11, and attach DO-NOT-CLOSE tags:
(a)
11B19, STAB TRIM ALT (IF INSTALLED)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-21
ALL ú ú 02 Page 405 ú Jan 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
(b)
11C12, STAB TRIM SHUTOFF LEFT
(c)
11C13, STAB TRIM SHUTOFF RIGHT
(d)
11H11 or 11C05, STAB TRIM CONT L
(e)
11H17, FLT CONT SHUTOFF TAIL LEFT
(f)
11H18, FLT CONT SHUTOFF TAIL CTR
(g)
11H20, STAB TRIM CONT R
(h)
11H28, FLT CONT SHUTOFF TAIL RIGHT
E.
Remove the Neutral Shift and Override Mechanism (Fig. 402)
S 494-011
(1)
Install rig pin E/ST7 in the aft quadrants.
S 494-012
(2)
Install rig pin E/ST10 in the neutral shift housing.
S 034-013
(3)
Disconnect the two control rods that connect the neutral shift mechanism to the feel and centering unit.
NOTE: Do not change the adjustment of the control rods.
____
S 034-014
(4)
Remove the three fasteners that connect the neutral shift link to the neutral shift mechanism at the stabilizer input lever.
S 034-015
(5)
Remove the two grounding springs that connect the neutral shift mechanism to the torque box bracket on the elevator aft mechanism.
NOTE: Each spring has a force of 150 pounds (667 newtons).
____
S 034-016
(6)
Remove the four fasteners that attach the neutral shift mechanism to the torque box of the elevator aft mechanism.
(7)
Remove the neutral shift and override mechanism.
S 024-017
TASK 27-31-21-424-018
3. Install the Neutral Shift and Override Mechanism________________________________________________
A. References
(1)
06-42-00/201, Empennage Access Doors and Panels
(2)
24-22-00/201, Electrical Power - Control
(3)
27-31-00/501, Elevator Control System
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-21
ALL ú ú 02 Page 406 ú Jan 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL
B. Access
(1)
Location Zones
211/212 Control Cabin
311/312 Area Aft of Pressure Bulkhead to BS 1787.45
313/314 Stabilizer Center Section Compartment
(2)
Access Panels
311AL Forward Stabilizer Compartment
313AL Elevator Neutral Shift and Override Mechanism
C.
Install the Neutral Shift and Override Mechanism (Fig. 402)
S 434-019
(1)
Install the four fasteners to attach the neutral shift mechanism to the torque box for the elevator aft mechanism.
S 434-020
(2)
Install the two grounding springs between the neutral shift mechanism and the torque box for the elevator aft mechanism.
S 434-021
(3)
Install the three fasteners to connect the neutral shift link to the neutral shift mechanism at the stabilizer input lever.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(129)
