曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (12) Manually lift the elevator trailing edge up and install the PCA lock assembly (Fig. 402).
 NOTE: A force of approximately 60 pounds (266 newtons) on the
____ elevator trailing edge is necessary to lift the elevator. The PCA lock assembly can be installed on the inboard, center, or outboard PCA.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-06
 ALL  ú ú 01 Page 405 ú Jan 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757 MAINTENANCE MANUAL
 S 044-014
 WARNING: DO THE DEACTIVATION PROCEDURE FOR THE SPOILERS OR MOVE ALL
_______ PERSONS AND EQUIPMENT AWAY FROM THE SPOILERS. THE SPOILERS CAN RETRACT QUICKLY AND CAUSE INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT.
 (13)
 Do the deactivation procedure for the spoilers (Ref 27-61-00) or move all persons and equipment away from the spoilers.

 S 864-015

 (14)
 Remove electrical power (Ref 24-22-00).

 E.
Remove the PCA Input Linkage (Fig. 401)

 NOTE: The steps that follow apply to the outboard, center, and inboard
____
 PCA linkages unless specified differently.

 S 034-016
 (1)  
On the center and outboard PCA linkages only, disconnect the centering spring from the crank assembly (View C and D).

 S 034-017

 (2)
Disconnect the two ends of the pogo rod and remove the pogo rod.

 NOTE: Do not change the adjustment of the pogo rod while it is
____ disconnected. If you do, you will have to adjust the elevator system.
 S 034-018
 (3)  
Disconnect the interconnect rods from the crank assembly.

 S 034-019

 (4)  
On the inboard PCA linkage only, disconnect the PCA input rod from the crank assembly (View B).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-06
 ALL  ú ú 01 Page 406 ú Dec 20/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

 S 034-020
 (5)  
Remove the fasteners, bearings, and bushings that connect the crank assembly to the swing link assembly (View A-A, B-B, and C-C).

 S 024-021

 (6)  
Remove the crank assembly.

 S 034-022

 (7)  
Remove the fasteners, bearings, and bushings that connect the swing link assembly to the support brackets (View A-A, B-B, and C-C).

 S 024-023

 (8)  
Remove the swing link assembly.

 TASK 27-31-06-424-024
 3. Install the PCA Input Linkage
_____________________________
 A. Consumable Materials
 (1)
D00633 Grease, Corrosion Preventive - BMS 3-33 (recommended)

 (2)
D00015 Grease, Corrosion Preventive - BMS 3-24 (optional)

 B.
References

 (1)  
06-42-00/201, Empennage Access Doors and Panels

 (2)  
27-31-00/501, Elevator Control System

 (3)  
27-61-00/201, Spoiler Speedbrake Control System

 C.
Access

 (1)  
Location Zones 211/212 Control Cabin 335/345 Horizontal Stabilizer, Rear Spar to Trailing Edge

 (2)  
Access Panels
 335DB/345DB Elevator PCAs

 D.
Install the PCA Input Linkage (Fig. 401)

 NOTE: Apply a layer of grease on all of the bolts, nuts, bearings and
____
 bushings before you install them.

 S 424-025
 (1)  
Install the fasteners, bearings and bushings to connect the swing link assembly to the support brackets (View A-A, B-B, and C-C).

 S 424-026

 (2)  
Install the fasteners, bearings and bushings to connect the crank assembly to the swing link assembly (View A-A, B-B, and C-C).

 (3)  
Connect the interconnect rods to the crank assembly.

 S 434-027
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(89)