3.  
Allow coating to dry for 15 minutes to 1 hour before recoating or touch-up, if required, after the initial coating.

4.  
After coating or touch-up, allow coating to dry for 15 minutes to 1 hour before removing masking.

SURFACE PREPARATION FOR PRESSURE SENSITIVE SAFETY WALK
1.  
Remove all contaminates and moisture.

2.  
Mask off area to protect painted surfaces.

3.  
Apply suitable stripper MEK Federal Spec. TT-M-261, U.S.Rubber No. 3339 to wing walk compound. As compound softens, remove with putty knife or other suitable tool.

4.  
Prime and paint area.

— Note —
For newly painted surfaces allow 2.5 hours minimum drying time before application of safety walk.
APPLICATION OF PRESSURE SENSITIVE SAFETY WALK
— Note —
Do not apply when surface to be coated is below 50°F.
1.  
Peel back full width of protective liner approximately 2 inches from leading edge of safety walk.

2.  
Beginning at leading edge, apply safety walk to wing area.  Verify proper alignment and position from wing flap.

3.  
Remove remaining protective liner as safety walk is being applied.

4.  
Roll firmly with a long handled cylindrical brush in both lengthwise directions.  Verify all edges adhere to wing skin.

5.  
Install and rivet leading edge retainer.

51-10-00 Page 51-18 Issued: April 1, 1997
3C8

CHAPTER

52

DOORS

THIS PAGE INTENTIONALLY BLANK

CHAPTER 52 - DOORS 
TABLE OF CONTENTS / EFFECTIVITY 
CHAPTER/ SECTION  SUBJECT  GRID NO.  EFFECTIVITY 
52-00-00  GENERAL  3C13 
Door Seal Snubbers Removal & Installation  3C13 3C13 
52-10-00  PASSENGER/CREW  3C16 
Door Assembly Removal Installation Adjustment Door Latch Mechanism Removal Installation Adjustment Door Lock Assembly Removal Installation  3C16 3C16 3C16 3C16 3C16 3C16 3C16 3C18 3C18 3C18 3C18 
Door Auxiliary Latch Removal Installation Adjustment  3C18 3C18 3C18 3C18 
52-20-00  EMERGENCY EXIT  3C20 
Removal and Installation  Testing  3C20 3C20 
52-30-00  CARGO  3C23 
Baggage Door Removal Installation  3C23 3C23 3C23 
Baggage Door Lock Assembly Removal  Installation  3C23 3C23 3C23 

52-Cont./Effec. Page 52-3 Issued: April 1, 1997
THIS PAGE INTENTIONALLY BLANK

52-Cont./Effec. Page 52-4 Issued: April 1, 1997
3C12
GENERAL.
This airplane is configured with a single passenger/crew door on the right side of the fuselage, over the wing. Access to the baggage compartment is through a small door also on the right side, just aft of the wing. Emergency egress is assisted by an emergency exit incorporated into the crews' left window.
DOOR SEAL SNUBBER.
REMOVAL AND INSTALLATION OF DOOR SEAL SNUBBERS. (Refer to Figure 52-1.)

1.
To remove old seals use a thinner. such as toluol, that won’t affect the painted surface, and strip off the old seal.

2.
Install the door seal as follows:

A. If the surface has just been painted, allow to dry for a minimum of 2 hours before installing the seal.
B. Wipe the surface clean with a cleaner solvent, such as DuPont Prepsol 3919S.
— Note —
Refer to the List of Consumable Materials in Chapter 91 for types of appropriate neoprene adhesive.
C. Make sure both the seal and surface are 65° to 100°F.

Figure 52-1. Door Snubber Installation 
52-00-00 
Page 52-5 
Issued: April 1, 1997 
3C13 

D.  Adhesive should only be applied to that area to be covered by the seal.  If necessary, tape off the affected area.  The adhesive can be thinned as required with toluol.  Apply adhesive in a continuous coat of .002 to .010 of an inch thick.
E.  Apply a continuous coat of adhesive of the same thickness to the seal.
F.  With the adhesive applied to the mating surface and seal, allow them to cure 30 to 60 min. apart before bonding them in place.
G.  With reference to Figure 52-1, make sure the seal is properly aligned before allowing the surfaces to come in contact. The seal should not be stretched or pulled such that the cross section of the seal is reduced or distorted. Make sure the door closes properly and that an airtight seal is produced.
H.  After positioning the seal, apply pressure to remove air bubbles and assure firm contact.
THIS SPACE INTENTIONALLY BLANK

52-00-00 Page 52-6 Issued: April 1, 1997
3C14
THIS PAGE INTENTIONALLY BLANK
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：西門諾爾飛機維護手冊 simenole PA-44-180 AMM 2(45)