曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

U  0.368  9.3472  6  0.204  5.1816  34  0.111  2.8194  63  0.037  0.9398 
23/64  0.3593  9.1262  13/64  0.2031  5.1594  35  0.110  2.794  64  0.036  0.9144 
T  0.358  9.1281  7  0.201  5.1054  7/64  0.1093  2.7781  65  0.035  0.899 
S  0.346  8.7884  8  0.199  5.0546  36  0.1065  2.7051  66  0.033  0.8382 
11/32  0.3437  8.7300  9  0.196  4.9784  37  0.104  2.6416  1/32  0.0312  0.7937 
R  0.339  8.6106  10  0.1935  4.9149  38  0.1015  2.5781  67  0.032  0.8128 
Q  0.332  8.4328  11  0.191  4.8514  39  0.0995  2.5273  68  0.031  0.7874 
21/64  0.3281  8.3337  12  0.189  4.8006  40  0.098  2.4892  69  0.029  0.7366 
P  0.323  8.2042  3/16  0.1875  4.7625  41  0.096  2.4384  70  0.028  0.7112 
O  0.316  8.0264  13  0.185  4.699  3/32  0.0937  2.3812  71  0.026  0.6604 
5/16  0.3125  7.9375  14  0.182  4.6228  42  0.0935  2.3749  72  0.025  0.635 
N  0.302  7.6708  15  0.180  4.572  43  0.089  2.2606  73  0.024  0.0696 
19/64  0.2968  7.5387  16  0.177  4.4958  44  0.086  2.1844  74  0.0229  0.58166 
M  0.295  7.4930  17  0.173  4.3942  45  0.082  2.0828  75  0.021  0.5334 
L  0.290  7.3660  11/64  0.1718  4.3656  46  0.081  2.0574  76  0.020  0.508 
9/32  0.2812  7.1425  18  0.1695  4.3053  47  0.0785  1.9939  77  0.018  0.4572 
K  0.281  7.1374  19  0.166  4.2164  5/64  0.0781  1.9844  1/64  0.0156  0.3969 
J  0.277  7.0358  20  0.161  4.0894  48  0.076  1.9304  78  0.016  0.4064 
I  0.272  6.9088  21  0.159  4.0386  49  0.073  1.8542  79  0.0145  0.3683 
H  0.266  6.7564  22  0.157  3.9878  50  0.070  1.778  80  0.0135  0.3429 
17/64  0.2656  6.7462 
DRILL SIZES AVAILABLE Drill may be obtained in regular sizes to a 4 inch diameter, and increase in 64ths of an inch. The regular metric drills vary from 2 to 76mm and increase in 0.5mm variations. 

91-00-00 Page 91-9 Issued: April 1, 1997
4B9

TIRE BALANCER BUILDING INSTRUCTIONS.
1.
Chamfer top edges of -3 sides, leaving 1/16 inch flat on top inboard edge.   Rivet -2 tee’s to -3 sides using AN 470-ADS rivets 2” spacing.  Use AN 426-ADS rivets 2” center to center to secure -2 tee’s to - 1 base. If tee extrusion is unavailable, heavy angle extrusion could be used. -3 sides must be vertical.

2.
The -4 axle must slide through the -8 pipe.  The -5 nuts were made by reaming the existing threads in the AN 365-624 nuts with an R drill, then tapping with a 1/8-27 pipe tap.

3.
The -6 spacers were made from 1/2 inch aluminum tubing.  The two lengths of spacers are suitable for balancing most any aircraft wheel.

4.
The -7 bushings may be made from one inch phenolic or aluminum using a 1-1/2 inch hole saw to cut out the smaller bushing and a 1-3/4 hole saw to cut out the larger. By inserting a 1/4 inch long threaded bolt through the pilot hole and securing with a washer and nut, a drill press and file may be used to make the off-set on the bushing.  The turned-down part should just slide inside the bearing race.  Ream the pilot hole to slide over the -8 pipe threads.

5.
The -8 pipe was made from a piece of 1/8 inch black pipe and threaded with a 1/8-27 pipe die.   Thread 3 inches in from each end of the pipe.

91-00-00 Page 91-10 Revised: February 28, 2002
4B10
CHART 9105.  LIST OF CONSUMABLE MATERIALS

MATERIAL  SPECIFICATION  PRODUCT  VENDOR 
Fuel, Engine Oil, Engine Corrosion Preventive Compound and Broken Oil Lubricating Oil (General Purpose Low Temperature) Oil Filter Air Filter Dry Lubricant Lubricating Oil Lubricating Grease (General Purpose superseded by MIL-G-81322) Lubricating Grease (High Temperature)  (See Note l) MIL-L-6082 or MIL-L-2285 1 (See Note 3) MIL-C-6529 Type II Per latest revision Lycoming Service Letter L121 MIL-L-7870 MIL-L-60326 MIL-L-7711 MIL-G-81322 (See Note 2)  100 octane green / blue Aero Lubriplate or Mag 1 (Purch.) Regal AFB2 Aeroshell Grease No. 6 2242 International Mobilgrease 28  Fiske Bros. Refining Co. 129 Lockwood St. Newark, N.J.  07105 (201)-589-9150 Texaco Inc. 2000 Westchester Ave. White Plains,N.Y. 10650 (914)-253-4000 Shell Oil Co. One Shell Plaza Houston, TX  77002 (713)-220-6697 Lubricants Co. New Orleans, La. Mobil Oil Corp. 150 E. 42nd St. New York, NY 10017 (212)-883-4242 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：西門諾爾飛機維護手冊 simenole PA-44-180 AMM 2(91)