曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

21-4.  Fuel Regulator and Shutoff Valve  1H16 
21-5.  Top View - Duct Switch  1H16 
21-6.  Intake Valve and Switches  1H17 
21-7.  Wiring Diagram (Heater)  1H21 
21-8.  Primary Power Circuit (Heater)  1H22 
21-9.  Starting Power Circuit (Heater)  1H23 
21-10.  Spark Plug Fixture (Heater)  1I1 
21-11.  Wiring - Test Setup (Heater)  1I1 
21-12.  Spark Plug Gap Adjustment (Heater)  1I2 
21-13.  Ignition Unit Assembly (Heater)  1I6 
21-14.  Test Setup for Fuel Regulator and Shutoff Valve (Heater)  1I9 
21-15.  Heater Fuel Pump  1I10 
21-16.  Suggested Design for Seal Plates, Plugs, and Caps for 
Combustion Tube leakage Test  1I14 
21-17.  Test Setup for Combustion Air Pressure Switch  1I14 
21-18.  Exploded View of Heater Assembly  1I19 
21-19.  Exploded View - Combustion Air Blower and Motor Assembly  1I22 
21-20.  Suggested Setup of Heater Operation Test  1I24 

Introduction Page 14
Revised: February 28, 2002
4A18
THE NEW PIPER AIRCRAFT, INC.
PA-44-180
AIRPLANE MAINTENANCE MANUAL

LIST OF ILLUSTRATIONS (cont) 
FIGURE NO.  SUBJECT  GRID NO. 
21-21.  Wiring Connections for Heater Operation Test  1I24 
21-22.  Spark Plug Gap Adjustment Tool  1J3 
21-23.  Heater Hourmeter Installation  1J4 
24-1.  Lamp Bank load  1J24 
24-2.  Battery Box  1K2 
24-3.  Electrical Component Location (Lamar Model No. B-00392-1)  1K5 
24-4.  Lamar B-00392-1 Regulator Overvoltage Test Method  1K6 
25-1.  Seat Back Lock  1K13 
25-2  Lumbar Seat Bladder Installation  1K15 
25-3.  Artex 110 ELT  1K18 
25-4.  Artex ELT 110 Wiring Schematic  1K19 
27-1.  Rod End Bearing Installation  2B8 
27-2.  Control Cable Inspection Technique  2B9 
27-3.  Cable Wear Pattern  2B10 
27-4.  Internal Cable Wear  2B10 
27-5.  Pulley Wear Patterns  2B12 
27-6.  Control Column Assembly  2B19 
27-7.  Flex (Universal) Joint Assembly  2B21 
27-8.  Aileron Controls  2B23 
27-9.  Bellcrank Rigging Tool  2C1 
27-10.  Aileron Rigging  2C2 
27-11  Rudder Controls  2C7 
27-12.  Clamping Rudder Pedals  2C9 
27-13  Rudder Rigging Tool  2C9 
27-14.  Rudder Rigging  2C9 
27-15.  Rudder Travel Adjustments  2C10 
27-16.  Rudder Trim Controls  2C12 
27-17.  Rudder Pedal Assembly  2C15 
27-18.  Stabilator Controls  2C17 
27-19.  Stabilator Rigging  2C20 
27-20.  Stabilator Travel Adjustments  2C22 
27-21.  Methods of Securing Trim Cables  2C22 
27-22.  Stabilator Trim Controls  2D3 
27-22a.  S-Tec Manual Electric Trim Clutch Check & Adjustment  2D5 
27-23.  Wrapping Trim Barrels  2D7 
27-24.  Stabilator Trim Screw Adjustment  2D7 
27-25.  Flap Controls and Rigging  2D12 
27-26.  Flap Step Adjustment  2D14 
27-27.  Flap Rigging Tool  2D15 
28-1.  Fuel System Installation  2D23 
28-2.  Fuel Cell Installation  2E5 
28-3.  Locking Fuel Cap Assembly  2E9 
Introduction 
Page 15 
Revised: February 28, 2002 
4A19 

THE NEW PIPER AIRCRAFT, INC.
PA-44-180
AIRPLANE MAINTENANCE MANUAL

LIST OF ILLUSTRATIONS (cont) 
FIGURE N0.  SUBJECT  GRID NO. 
28-4.  Fuel Filter Assembly  2E12 
28-5.  Fuel Selector Valve  2E13 
28-6.  Fuel Gauge  2E16 
28-7.  Fuel Pressure Gauge and Calibration  2E17 
29-1.  Schematic Diagram of Hydraulic System  2F3 
29-2.  Hydraulic Pump (Sheet 1 of 2)  2F13 
29-2.  Hydraulic Pump (Sheet 2 of 2)  2F14 
29-3.  Nose Gear Actuating Cylinder  2F17 
29-4.  Main Gear Actuating Cylinder  2F19 
29-5.  End Gland Locking Device (Main Gear)  2F19 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：西門諾爾飛機維護手冊 simenole PA-44-180 AMM 2(85)