If the LRU tells the CMCF the software is not compatible with other software loaded in the LRU, the message shows:
* The load part number is not compatible with the software of the destination LRU.
If the LRU tells the CMCF the software is not compatible with other LRU software in the system, the message shows:
* The load part number is not compatible with software loaded in the other LRUs in this system.
EFFECTIVITY
BEJ ALL
If the LRU tells the CMCF the software is not compatible with LRU, the message shows:
* The load part number is not compatible with the hardware of the destination LRU.
If the LRU tells the CMCF the software is not compatible with airplane, the message shows:
* The load part number is not compatible with the airplane.
The buttons are:
*
OVERRIDE
*
STOP
*
HELP
The OVERRIDE selection shows if an override capability exists. Select OVERRIDE to continue the load process.
Select STOP to end the data load process, close the dialog box and return to the data load main display.
Select HELP to show the help dialog box for the destination LRU incompatibility dialog box. Help text for the dialog box must be in the CMCF AMI for HELP to show.
Data Transfer Error Dialog Box
The data transfer error dialog box shows when the load transfer process ends because of a data transfer error.
45-10-00
Page 98.83 D633W101-BEJ Sep 05/2002
CMCS -DATA LOAD MESSAGE DIALOG BOXES -2
The message field shows:
*
The data load stopped.
*
The signal became incorrect.
*
Usually, the destination LRU cannot operate.
The buttons show:
*
STOP
*
HELP.
Select STOP to close the dialog box and return to the data load main display.
Select HELP to show the help dialog box for the data transfer error dialog box. Help text for the dialog box must be in the CMCF AMI for HELP to show.
Data Storage Error Dialog Box
The data storage error dialog box shows when the destination LRU/LRM cannot validate the data load.
The message field shows:
*
The destination cannot make sure the new load part number is loaded correctly.
*
If this is the first time that the data load has stopped, select TRY AGAIN.
* If this is the second time the data load has stopped, select CHECK DISK. The select TRY AGAIN if the load part number is good.
The command selections are:
*
TRY AGAIN
*
STOP
*
HELP
*
CHECK DISK.
Select TRY AGAIN to start the full load process for the same source and destination selections.
Select STOP to close the dialog box and return to the data load main display.
Select HELP to show the help dialog box for the data storage error dialog box. Help text for the dialog box must be in the CMCF AMI for HELP to show.
Select CHECK DISK to start the disk validation procedure.
Data Transfer Completion Dialog Box
The data transfer completion dialog box shows that the transfer of data is complete for the current load process.
The message field shows:
EFFECTIVITY BEJ ALL 45-10-00
Page 98.84
D633W101-BEJ Sep 05/2002
CMCS -DATA LOAD MESSAGE DIALOG BOXES -2
*
Wait for the destination LRU to start.
*
If you wait more than fifteen minutes, select STOP.
The buttons are:
*
STOP
*
HELP.
Initially, the STOP selection does not show. The STOP selection shows if the destination LRU/LRM does not respond within ten minutes.
Select STOP to close the dialog box and return to the data load main display.
Select HELP to show the help dialog box for the data transfer completion dialog box. Help text for the dialog box must be in the CMCF AMI for HELP to show.
Data Load Completion and Configuration Verification
The data load completion and configuration verification dialog box shows that the load process is complete and successful.
The message field has several items. These items are:
*
The data load is complete. The current LRU configuration is shown below.
*
LRU Part Number:
*
Hardware Part Number:
*
Serial Number:
EFFECTIVITY
BEJ ALL
If necessary, a scroll bar may show to enable the user to scroll through the text.
The buttons are:
*
CONTINUE
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：777 AMM 飛機維護手冊 中央維護 Central Maintenance(41)
