CMCS -HELP FUNCTION
EFFECTIVITY BEJ ALL 45-10-00
Page 98.229
D633W101-BEJ Sep 05/2002
777 AIRCRAFT MAINTENANCE MANUAL
THIS PAGE IS INTENTIONALLY LEFT BLANK
45-10-00
Page 98.230 D633W101-BEJ Sep 05/2002
CMCS -REPORT OUTPUT DEVICE DIALOG BOX
General
The CMCF can generate reports from user inputs, from a ground station request or when events cause an automatic report.
The CMCF sends a print image of the reports to the flight compartment printer. The CMCF sends reports to the disk drive and a ground station are in a compressed format.
The CMCF can complete one report at a time. You may send another report after the CMCF complets the first report.
Report Menu Selections
When you select any item on the report menu bar or select REPORT DATA on any dialog box, the output device dialog box shows.
Select REPORT PAGE DATA to cause a report to go to the output device for the information that shows on the display.
Dialog Box Characteristics
The dialog box has:
*
Title
*
Exclusive source selections
*
Printer output device selection
*
Disk drive output device selection
EFFECTIVITY
BEJ ALL
*
Data link output device selection
*
Buttons.
Title
The title shows REPORT: followed by the item from the menu selection or the dialog box.
Printer Output Device Selection
The printer area has:
*
Title
*
Buttons
*
Text area.
The buttons are SEND and STOP. When you select SEND the CMCF sends the report to that device. The SEND button is not available during these times:
*
When the output device is not available
*
During the transmission of a report to that device
*
After the selection of OUTPUT STATUS on the menu bar.
Select STOP to abort the report in progress.
The text area shows the status of the transmission to the printer. These are the possible messages:
*
Transmission in Operation
*
Door Open/Printer out of Paper
*
Printer Busy
45-10-00
Page 98.231 D633W101-BEJ Sep 05/2002
CMCS -REPORT OUTPUT DEVICE DIALOG BOX
*
Cannot Connect to the Printer. The Printer is Inactive/Faulted
*
Cannot Connect to the Printer. The Printer Does not Give a Reply
*
Transmission Completed.
Disk Drive Output Device Selection
The disk drive area has:
*
Title
*
Buttons
*
Text area.
The buttons are SEND and STOP. Their function here is the same as the printer area.
The text area shows the status of the transmission sent to the disk drive. These are the possible messages:
*
Transmission in Progress
*
Insert Disk
*
Change Disk
*
Disk Write Protected
*
Cannot Connect to the Disk Drive. The Disk Drive is Inactive/ Faulty
*
Cannot Connect to the Disk Drive. The Disk Drive Does not Give a Reply
*
Transmission Completed to Disk Drive.
Datalink Output Device Selection
The datalink area has:
*
Title
*
Buttons
*
Text area.
The buttons are SEND and STOP. Their function here is the same as the printer area.
The text area shows the status of the transmission sent to datalink. These are the possible messages:
*
Transmission in Progress
*
Datalink SYS Faulted
*
Datalink Lost
*
Disk Write Protected
*
Transmission Completed to Ground.
Buttons
Select HELP to show the help dialog box for the report output device dialog box. Help text for the dialog box must be in the CMCF AMI for HELP to show.
Select GO BACK to remove the dialog box and return to the previous display.
EFFECTIVITY BEJ ALL 45-10-00
Page 98.232
D633W101-BEJ Sep 05/2002
777 AIRCRAFT MAINTENANCE MANUAL
CMCS -REPORT OUTPUT DEVICE DIALOG BOX
EFFECTIVITY BEJ ALL 45-10-00
Page 98.233
D633W101-BEJ Sep 05/2002
777 AIRCRAFT MAINTENANCE MANUAL
THIS PAGE IS INTENTIONALLY LEFT BLANK
45-10-00
Page 98.234 D633W101-BEJ Sep 05/2002
CMCS -DOWNLINK REPORTS
General
Datalink reports are changed into short codes to lower the cost of using a satellite or ground station. 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：777 AMM 飛機維護手冊 中央維護 Central Maintenance(68)
