29-22-01
 ALL  ú ú 04 Page 408 ú May 28/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757 MAINTENANCE MANUAL
 S 864-063
 (33)
 Set the R ELEC PUMP switch, on the overhead panel, P5, to the OFF position.

 S 724-064

 (34)
 Make sure the EICAS message POWER XFER UNIT does not show on the status or maintenance display.

 S 864-065

 (35)
 Remove hydraulic power if it is not necessary (AMM 29-11-00/201).

 S 164-066

 (36)
 Clean all hydraulic fluid from the installation area (AMM 12-25-01/301).

 S 614-067

 (37)
 Fill the reservoirs in the left and right hydraulic systems (AMM 12-12-01/301).

 CAUTION:_______ QUICKLY CLEAN ALL OF THE HYDRAULIC FLUID FROM THE INSTALLATION
 AREA.  HYDRAULIC FLUID CAN CAUSE DAMAGE TO THE AIRPLANE
 EQUIPMENT.

 S 094-036
 WARNING: USE THE PROCEDURE IN AMM 32-00-15/201 TO REMOVE THE DOOR LOCKS.
_______ THE DOORS OPEN AND CLOSE QUICKLY AND CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (38) Remove door locks from the landing gear doors and close the doors (AMM 32-00-15/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 29-22-01
 ALL  ú ú 04 Page 409 ú May 28/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
 POWER TRANSFER UNIT (PTU) PRESSURE FILTER MODULE AND COMPONENTS -
_________________________________________________________________ REMOVAL/INSTALLATION
____________________
 1.  General_______
 A.  This procedure has two tasks. One task removes the filter module and the components for the pressure of the power transfer unit (PTU). The other task installs the filter module and the components.
 TASK 29-22-02-004-001
 2.  Remove the Filter Module and the Components (Fig. 401)___________________________________________
 A.  General
 (1)  
This task contains procedures which remove the components which follow:

 (a)  
Filter module for the pressure of the power transfer unit

 (b)  
Filter element

 (c)  
Pressure switches

 (d)  
Check valve

 (e)  
Differential pressure indicator.

 (2)  
To start one of these procedures, do the "Prepare for Removal" group of steps. Then, do the applicable group of steps that is necessary to remove the component.

 B.  References
 (1)  
AMM 29-11-00/201, Main (Left, Right, and Center) Hydraulic Systems

 (2)  
AMM 32-00-15/201, Main Gear Door Locks

 (3)  
AMM 32-00-20/201, Landing Gear Downlocks

 C.  Access
 (1)  Location Zone
 143 MLG Wheel Well

 D.  Prepare for Removal
 S 494-002
 (1)  Make sure the downlocks are installed on the nose and main landing gear (AMM 32-00-20/201).
 S 494-003
 WARNING: DO THE PROCEDURE IN AMM 32-00-15/201 TO INSTALL THE DOOR LOCKS.
_______ THE DOORS OPEN AND CLOSE QUICKLY AND CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (2)  
Open the doors for the landing gear and install the door locks (AMM 32-00-15/201).

 S 864-004
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 液壓 CHAPTER 29 - HYDRAULIC POWER 2(139)