NOTE: Align the index mark on the front shell of the mounting frame
____ with the zero mark on the face of the indicator dial before you tighten the nuts.
 S 434-011
 (4)  
Connect the electrical connector.

 S 864-012

 (5)  
Remove the DO-NOT-CLOSE tags and close these circuit breakers on the overhead panel, P11:

 (a)  
11K19, HYDRAULICS QTY CTR

 (b)  
11K20, HYDRAULICS QTY LEFT

 (c)  
11K21, HYDRAULICS QTY RIGHT

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 29-18-03
 ALL  ú ú 01 Page 403 ú Dec 20/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

 (6)  S 864-013Supply electrical power (AMM 24-22-00/201).
 (7)  S 864-014Move the fill selector valve to the left, right, or the center system.
 (8)  S 604-015Fill the hydraulic system reservoir, that you set the fill selector valve to, until you can see the fluid level in the center of the reservoir sight glass (Ref 12-12-01).
 (9)  S 214-016Make sure the fill indicator shows 6.1-7.1 gallons (23.1-26.9 liters) for the left or right system and 3.0-4.0 gallons (11.3-15.1 liters) for the center system.
 S 864-018

 (10)
 Move the fill selector valve to the CLOSED position.

 S 414-019

 (11)
 Close the access door for the hydraulic service bay, 197KL (AMM 06-41-00/201).

 S 864-020

 (12)
 Remove the electrical power if it is not necessary (AMM 24-22-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 29-18-03
 ALL  ú ú 01 Page 404 ú May 28/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
 RESERVOIR FILL FILTER MODULE AND COMPONENTS - REMOVAL/INSTALLATION
__________________________________________________________________
 1.  General_______
 A.  This procedure contains steps to remove and install the filter module and the filter element for the reservoir fill.
 TASK 29-18-04-024-001
 2.  Remove the Filter Module and the Filter Element_______________________________________________
 A.  General
 (1)  This task contains two procedures, one to remove the filter module and one to remove the filter element. Because this task contains two procedures, only the applicable group of steps must be done.
 To start one of these procedures, do the "Prepare for the Removal" group of steps. Then, do the group of steps that is necessary to remove the component.
 B.  References
 (1)  
AMM 06-41-00/201, Fuselage Access Doors and Panels

 (2)  
AMM 29-11-00/201, Main (Left, Right, and Center) Hydraulic Systems

 C.  Access
 (1)  
Location Zones
 197 Wing to Body - Aft Lower Half (Left)

 (2)  
Access Panel
 197KL Central Hydraulic Service Center

 D.  Remove the Filter Module (Fig. 401)
 S 864-002
 (1)  
Remove the pressure from the hydraulic systems and reservoirs (AMM 29-11-00/201).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 液壓 CHAPTER 29 - HYDRAULIC POWER 2(36)