S 864-038
 (13)
 Pressurize the right hydraulic system and reservoir
 (AMM 29-11-00/201).

 S 824-039

 (14)
 Do the adjustment for the door link (AMM 29-21-00/501).

 S 834-040

 (15)
 Do the adjustment for the stowed limit switch (AMM 29-21-17/201).

 H.  Install the Hydraulic Pump (Fig. 402)
 S 824-073
 (1)  Do the steps that follow to find the thickness of the shims (29) for each of the hydraulic tubes (24, 25, 26):
 NOTE: Do not install the O-rings, backup rings, or shims at this
____
 time.

 (a)  Do the steps that follow to measure dimension A on each hydraulic tube (24, 25, 26): 1) Install the hydraulic tubes (24, 25, 26) in the RAT strut
 housing (16). 2) Tighten the tube nut (27), on each hydraulic tube (24, 25, 26), by hand until it touches the end flange (28).
 3)  Measure the clearance, on each hydraulic tube (24, 25, 26), between the surface of the RAT strut housing (16) and the inner face of the tube nut (27).
 4)  For each hydraulic tube (24, 25, 26), write this clearance as dimension A in Table I.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 29-21-01
 ALL  ú ú 04 Page 411 ú Sep 28/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

 ~.............................................................................. | TABLE I | ................................................................................ | CALCULATE THE THICKNESS OF A SHIM FOR THE RAT | | STRUT HOUSING END OF EACH HYDRAULIC TUBE | ................................................................................ | | CASE DRAIN TUBE | OUTLET TUBE | INLET TUBE | ................................................................................
 |  |  |  |  |
 |  DIMENSION D  |  ________  |  ________  |  ________  |
 |  |  |  |  |

 ................................................................................ | | | | | | DIMENSION A | ________ | ________ | ________ | | | | | | ................................................................................ | SUBTRACT DIMENSION A FROM | | | | | DIMENSION D TO GET THE SHIM | | | | | THICKNESS (|0.003) WHICH IS | | | | | NECESSARY | ________ | ________ | ________ | | | | | | ................................................................................ | WRITE THE THICKNESS OF THE | | | | | SHIM WHICH YOU USE | ________ | ________ | ________ | | | | | | 2...............................…..................…..............…............1
 5)  Remove the hydraulic tubes (24, 25, 26) from the RAT strut housing (16).
 (b)  Do the steps that follow to measure dimension B on each hydraulic tube (24, 25, 26): 1) Install the hydraulic tubes (24, 25, 26) in the hydraulic
 pump housing (17). 2) Tighten the tube nut (27), on each hydraulic
 tube (24, 25, 26), by hand until it touches the end
 flange (28). 3) Measure the clearance, on each hydraulic tube (24, 25, 26),
 between the surface of the hydraulic pump housing (17) and
 the inner face of the tube nut (27).
 4)  For each hydraulic tube (24, 25, 26), write this clearance as dimension B in Table II.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 液壓 CHAPTER 29 - HYDRAULIC POWER 2(75)