曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

4. Lay the canopy on its right side. (Note: A mirror image
of the layout is permissible).
5. Flake the canopy so the top seams are even. Place a
clamp on the top of the canopy in line with each line
attachment point as in figure 5-73 on page 5-34.
Figure 5-69. Ram-air canopy packing tools.
Figure 5-70.Tying toggles.
Figure 5-71. Anchor risers.
Figure 5-72. Pull slider down.
5-33
STEP 2. STACKING AND PLEATING THE
RESERVE CANOPY
Note: The canopy stack should look like figure 5-74.
It is imperative that the rigger maintains control over the
packing process at all times. In particular, it is important
to keep the lines taut and straight and to keep the center
“wind channel” of the canopy stack clear and the line
attachment tabs stacked neatly.
1. Pull tension on the “A” lines. Split the leading edge in
half. [Figure 5-75]
2. Fold half under “A” lines. [Figures 5-76 and 5-77]
3. Pick up the “B” lines by the clamp and hold vertically
over the “A” clamp. [Figure 5-78] Note the spread of
the leading edge panels.
4. Lower the “B” clamp and material down to the “A”
clamp. [Figure 5-79] Spread the cells equally to both
sides. Keep the center cell in the middle.
Figure 5-73. Clamps on top of canopy.
TRAILING EDGE
(TAIL)
􀀀
􀀀
LEADING EDGE
(NOSE)
3 — PANELS
3 — PANELS
4 — PANELS
Control Line
D Lines
C Lines
B Lines
A Lines
Figure 5-74. Drawing of canopy stack.
5-34
5. Repeat this step with the “C” [Figure 5-80] and the
“D” line groups. [Figure 5-81]
Figure 5-75. Split the leading edge.
Figure 5-76. Fold half under “A” lines.
Figure 5-77. Smooth panels under “A” lines.
Figure 5-78. Hold “B” clamp vertically over “A” clamp.
Figure 5-79. Lower “B” clamp to “A” clamp, spreading the cells.
Figure 5-80. Repeat with “C” lines.
Figure 5-81. Repeat with “D” lines.
5-35
6. Split the trailing edge and separate the control lines
into right and left groups. [Figure 5-82]
7. Remove the “D” clamp. Hold down the “D” lines at
the line attachment point and pull down the control
lines. [Figure 5-83] Do not disturb the center of the
canopy stack.
STEP 3. SETTING THE BRAKES
1. Set the deployment brakes and stow the excess line in
the Velcro® keepers. [Figure 5-84]
2. The finished toggles should look like figure 5-85.
STEP 4. FOLDING THE CANOPY
1. Fold all the trailing edge to one side, then pull the
stabilizer panel taut. [Figure 5-86]
Figure 5-82. Split the trailing edge.
Figure 5-83. Pull down the trailing edge.
5-36
Figure 5-84. Set the deployment brakes.
Figure 5-85. Completed brakes.
Figure 5-86. Pull stabilizer taut.
5-37
2. Flake the trailing edge of the canopy starting with the
outboard control lines. Fold each cell in half on top of
the “D” line group [Figure 5-87] until you get to the
center.
3. Repeat with the opposite side.
4. Pull the slider up to the slider stops.
5. Remove remaining clamps from top of canopy. Make
sure all suspension lines are in the center of the canopy
stack. [Figure 5-88]
6. Fold the center of the trailing edge back to expose the
center of the “wind channel.” [Figure 5-89]
7. Create an “S” fold in the stack. [Figure 5-90]
8. Position a packing paddle a third of the way up from
the bottom of the canopy length on top of the stack.
[Figure 5-91]
9. Place a gun cleaning rod at half the distance between
the bottom and the packing paddle under the stack.
Figure 5-87. Flake the tail.
Figure 5-88. Lines are taut in the center.
Figure 5-89. Fold tail back for wind channel.
Figure 5-90. “S” fold drawing.
Figure 5-91. Packing paddle at 1/3rd location.
10. Pull the rod up and move the canopy with paddle
towards container. [Figure 5-92]
11. Pull the top center cell panel down to the bottom of
the stack.
12. Wrap the center cell around the folded canopy with
the left and right about halfway to the center, then
secure with clamps, starting at the bottom. [Figure
5-93] The width of the folded canopy should be the
width of the D-bag plus 2 inches (5cm).
13. Continue to wrap the center cell around the canopy
stack and secure with additional clamps. [Figure 5-94]
STEP 5. PLACING THE CANOPY INTO THE
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Parachute Rigger Handbook(54)