曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

7-18
Parachute Repair Procedure
TITLE: 7.1.6 Square Canopy – Rib Repair
NUMBER OF PAGES: 3
APPLICABLE PRODUCTS: Square canopies; main and reserve.
DESCRIPTION: Rib repair on a square canopy.
AUTHORIZED REPAIRMEN: FAA Master Parachute Rigger
MATERIALS: E thread
Fabric—type and color to match
Reinforcing tape—type and color as per original
MACHINES: 301 Straight Stitch—Medium Duty 7-11 SPI
1" x 42 stitch bar tack
Double needle with puller attachment [Optional]
SPI to match original
EQUIPMENT:
Scissors
Seam ripper
Marking pencil
Ruler
Pin board
Straight pins
Patching square
PROCEDURE
Note: Repairing a rib of a square canopy is similar to doing a partial panel repair. The biggest difference
comes when the rib is either [1] a “loaded” rib or one with support tapes for the line attachment
points, or [2] a crossport is damaged and needs to be repaired and recut. In this case, the
crossport area needs replacement [Figure A].
1.0 DISASSEMBLY:
1.1 Determine the extent of the damaged area and unpick the
top and bottom seams to access the rib [Figure B]. In most
cases, restitching the rib to the top and bottom panels is
fairly straightforward. Because of this, opening up the
seam for a good distance (18" plus either side of the proposed
patch) will allow easier access and sewing.
1.2 Pin the damaged rib to the pin board to stabilize the material
for marking. Mark out the damaged portion of the
panel, following the weave of the fabric [Figure C]. This
will be the patch fold lines and the limits of the partial rib
panel. Note that the tears of the crossports have been taped
together and that the crossport has been pinned down to
stabilize the fabric during the marking process.
1.3 Using the patching square, mark a parallel line .75" inside
the patch fold lines and then another one .62" inside the
second line [Figure D]. The inner lines will be the trim
lines for the rib patch.
7-19
2.0 REASSEMBLY:
2.1 Cut a piece of fabric approximately 4" wider and longer than the damaged panel area. Make
sure that one of the width edges is straight and even with the weave of the fabric.
2.2 Fold the straight edge .75" from the edge and pin in place across the damage line. Make sure
the fabric is centered on the existing panel.
2.3 Remove the pins from the crossport area and smooth the new panel fabric over the damaged
panel.
2.4 Fold the new fabric outwards at the patch fold mark and pin in place. Use the patching square
to mark a line at .75" in from the fold line [Figure E].
2.5 Trim the repair panel at the inner line [Figure F], fold under and pin in place.
2.6 Check the tension of the two panels. They should be equal. Mark the top and bottom edges
[Figure G] and the crossport location [Figure H].
2.7 Remove the rib from the pin board. Sew the two outboard seams approximately .06" from the
edge with the single needle [Figure J].
2.8 Trim the original damaged panel to the trim lines [Figure K]. Fold the fabric under to create
a French fell seam. Repeat with the opposite seam [Figure L].
7-20
2.9 Sew the inside row to complete the seam [Figure M].
2.10 Cut the new crossport to match the original location and shape [Figure N].
2.11 Trim the top and bottom edges as marked [Figure O].
2.12 Pin the top seam back onto the top panel. Sew in place with either the single needle or if
available, with the double needle machine and puller [Figure P]. Repeat with the bottom
seam.
2.13 Inspect finished work [Figure Q].
3.0 INSPECTION:
3.1 Seam alignment should be straight.
3.2 Check the tension of the replaced rib material.
3.3 Make sure the seams are restitched correctly.
3.4 Verify that the crossport is cut correctly.
3.5 The line attachment tape must be replaced correctly with no twists in the suspension line.
7-21
7-22
Parachute Repair Procedure
TITLE: 7.1.7 Square Canopy – Pilot Chute Attachment Point Repair
NUMBER OF PAGES: 2
APPLICABLE PRODUCTS: Square main canopies.
DESCRIPTION: Repair of the main canopy pilot chute attachment point.
AUTHORIZED REPAIRMEN: FAA Master Parachute Rigger
MATERIALS: E thread
Fabric—type and color to match
Reinforcing tape—type and color to match
Reinforcing fabric—type and color to match
MACHINES: 301 Straight Stitch—Medium Duty 7-11 SPI
308 Zigzag—Medium Duty 7-11 SPI
1" x 42 stitch bar tack
EQUIPMENT:
Scissors
Seam ripper
Marking pencil
12" ruler
PROCEDURE
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Parachute Rigger Handbook(74)