5. Close-up
Subtask 05-21-20-410-050
A. Close Access R (1) Close the avionic-compartment access door 811.
(2) Remove the access platform(s).
TASK 05-21-20-200-002
Zonal Inspection as far as Visible from the Ground of the Nose Gear Well (Zones 123)
1. Reason for the Job
R R Self Explanatory
2. Job Set-up Information
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
32-22-00-010-001 Nose Gear Doors - Ground Doors Opening
32-22-00-410-001 Nose Gear Doors - Ground Doors Closing
3. Job Set-up
Subtask 05-21-20-010-051
A. Get Access
(1) Open the nose landing gear doors 713 and 714. (Ref. TASK 32-22-00-010-001)
4. Procedure
Subtask 05-21-20-210-051
A. Inspection
(1)
Do a general visual inspection of the nose gear well (Zones 123 and 124).
(2)
Make sure that there are no signs of corrosion, cracks or damage.
(3)
Make sure that all the installations (wiring, ducting, piping) are attached correctly.
5. Close-up Subtask 05-21-20-410-051
A. Close Access
(1) Close the nose landing gear doors 713 and 714. (Ref. TASK 32-22-00-410-001)
R 1EFF : ALL 1 05-21-20 Page 604 1 1 Nov 01/03 1 1 1CES 1
TASK 05-21-20-200-003
Zonal Inspection of the Lateral Avionics Compartment
1.
Reason for the Job
Refer to the MPD TASK: ZL-125-01
2.
Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific access platform 3.5 m (11 ft. 6 in.)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
05-21-20-991-002 Fig. 601
05-21-20-991-007 Fig. 602
3. Job Set-upR **ON A/C 001-049, 051-099, 101-105, 151-156, 201-209,
Subtask 05-21-20-010-052
A. Get Access R (1) Put an access platform in position at zones 125 and 126.
(2) Open the access doors 125AL, 822 and 812. (Ref. Fig. 601/TASK 05-21-20-991-002, 602/TASK 05-21-20-991-007)
R Access Doors of the Avionic Compartment (Left Side) Figure 601/TASK 05-21-20-991-002
1 1EFF : 1 1CES ALL 1 1 11 05-21-20 Page 606 May 01/05
R Access Doors of the Avionic Compartment (Right Side) Figure 602/TASK 05-21-20-991-007
1EFF : ALL 1 05-21-20 Page 607 1 1 May 01/05 1 1 1CES 1
R **ON A/C 106-149, 157-199, 210-299, 301-399, 401-499,
R Subtask 05-21-20-010-052-A
R A. Get Access
R R R R (1) Put an access platform in position at zones 125 and 126. (2) Open the access doors 822 and 812. (Ref. Fig. 601/TASK 05-21-20-991-002, 602/TASK 05-21-20-991-007) **ON A/C ALL
4. Procedure_________
Subtask 05-21-20-210-052
R A. Inspection (1) Do a general visual inspection of the lateral avionics compartment. (2) Make sure that there are no signs of corrosion, cracks or damage. (3) Make sure that all the installations (wiring, ducting, piping) are attached correctly. 5. Close-up________ **ON A/C 001-049, 051-099, 101-105, 151-156, 201-209,
Subtask 05-21-20-410-052
A. Close Access
(1) Close the access doors 125AL, 822 and 812. (2) Remove the access platform(s).
R **ON A/C 106-149, 157-199, 210-299, 301-399, 401-499,
R Subtask 05-21-20-410-052-A
R A. Close Access
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 時間限制/維護檢查 3(18)
