3. Job Set-up__________
Subtask 05-23-20-010-056
A. Get Access
(1) Put an access platform in position at the zone 320.
R R R R (2) Remove the access panels: 325BL, 325CL, 325DL, 325EL, 325BR, 325CR, 325DR, 325ER, (Ref. TASK 55-33-13-010-001) or (Ref. TASK 55-33-13-010-002) 325AL, 325AR. (Ref. TASK 53-55-12-000-001)
4. Procedure_________
Subtask 05-23-20-210-056
A. Inspection
(1) Do a general visual inspection of the trailing edge of the vertical stabilizer.
(2) Make sure that there are no signs of corrosion, cracks or damage.
(3) Make sure that all the installations (wiring, ducting, piping) are attached correctly.
5. Close-up________
Subtask 05-23-20-410-056
A. Close Access
R R R (1) Install the access panels: 325AL, 325AR, (Ref. TASK 53-55-12-400-001) 325BL, 325CL, 325DL, 325EL, 325BR, 325CR, 325DR, 325ER, (Ref. TASK 55-33-13-410-001) or (Ref. TASK 55-33-13-410-002)
(2) Remove the access platform(s).
TASK 05-23-20-200-008
R Zonal Inspection of Rudder
1. Reason for the Job
__________________
Refer to the MPD TASK: ZL-326-02
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific access platform 10 m (32 ft. 10 in.)
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
Material No. 08-061 USA MIL-T-4053 TAPE SOUND DAMPENINGALUMINIUM FOIL (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
53-55-12-000-001 Removal of the Rudder Fairings 325AL and 325AR 53-55-12-400-001 Installation of the Rudder Fairings 325AL and 325AR 55-33-13-010-001 Opening of the Trailing Edge Access-Panels 325EL,
325ER, 325DL, 325DR, 325CL, 325CR, 325BL and 325BR
55-33-13-010-002 Opening/Removal of the Trailing Edge Access-Panels 325EL, 325ER, 325DL, 325DR, 325CL, 325CR, 325BL and 325BR
55-33-13-410-001 Closing of the Trailing Edge Access-Panels 325EL, 325ER, 325DL, 325DR, 325CL, 325CR, 325BL and 325BR
55-33-13-410-002 Closing/Installation of the Trailing Edge Access-Panels 325EL, 325ER, 325DL, 325DR, 325CL, 325CR, 325BL and 325BR
55-44-11-000-001 Removal of the Rudder Tip
55-44-11-400-001 Installation of the Rudder Tip
3. Job Set-up
__________
Subtask 05-23-20-010-057
A. Get Access
(1)
Put an access platform in position at the zone 320.
(2)
Remove the access panels:
R 325BL, 325CL, 325DL, 325EL, (Ref. TASK 55-33-13-010-001) or (Ref. TASK 55-33-13-010-002) 325AL, (Ref. TASK 53-55-12-000-001) 326AT. (Ref. TASK 55-44-11-000-001)
(3) Remove and discard the aluminium foil from the lightening holes in the front spar.
4. Procedure
_________
Subtask 05-23-20-210-057
A. Inspection
(1)
Do a general visual inspection of the rudder.
(2)
Make sure that there are no signs of corrosion, cracks or damage.
(3)
Make sure that all the installations (wiring, ducting, piping) are attached correctly.
5. Close-up
________
Subtask 05-23-20-410-057
A. Close Access
(1)
Cut and install the BONDING AND ADHESIVE COMPOUNDS (Material No. 08-061) over the lightening holes on the front spar.
(2)
Install the access panels:
326AT,
(Ref. TASK 55-44-11-400-001)
325AL,
(Ref. TASK 53-55-12-400-001)
325BL, 325CL, 325DL, 325EL.
(Ref. TASK 55-33-13-410-001) or (Ref. TASK 55-33-13-410-002).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 時間限制/維護檢查 3(62)
