VOR Flag Not Valid
03

Air Data Flag Not Valid
04

DADS Altitude Not Valid 05 VOR Excitation Missing 06 2x5 Tuning lines do not compare 07 No DME Pulse Pair 08 DME Range <0 Miles 09 DME Range >202 Miles 10 Range <2~h (~h = difference between airplane altitude
and station altitude)
11 DME Range Error >40 Miles
12 VOR Bearing Error >15 Degrees
13 DME Range Rate Unreasonable
14 Dual DME Station Separation …30` or ’150`
15 DME Error Unreasonable
16 VOR Error Unreasonable
17 ~R Error Unreasonable
18 ~R No. 1 Error Unreasonable
19 ~R No. 2 Error Unreasonable

~R = Distance between computed range and measured DME range
Radio Update Advisory Codes
Figure 102

EFFECTIVITY
CONFIG 3 AIRPLANES WITH LTN-72RL INS
799 Page 106
Apr 25/86
34-41-00
A. INS Startup and Data Base Validity Check (LTN-92)
(1)  
Place MSU mode selector switch to STBY.

(2)  
Verify the following on the CDU display:

(a)  
Top line displays PGM 92-04-10.

(b)  
CUSTOM DBASE is displayed between entry line markers.

(c)  
The fourth line displays the airline code and data base expiration date: SNXXXX.

____ The first two X's are the month of expiration, and the last
NOTE:
two X's are the year of expiration.

(d)  
The fifth line displays CLR: CONTINUE

(e)  
Press CDU CLR pushbutton. Verify that POSITION page is displayed.

B. INS Startup and Data Base Validity Check (LTN-72RL)
(1)  
Place MSU mode selector switch to STBY.

(2)  
Verify the following on the CDU display:

(a)  
Title of data base (geographical zones for example USA and CANADA, or MEDITERRANEAN) is on top line.

(b)  
PROGRAM 72-73-00 is on second line.

(c)  
Prompt/display line between entry line markers contains dashes for entry of present day, month, and year.

(3)  
Enter todays date by pressing CDU pushbuttons corresponding to digits for day, month, and year, in that sequence.

(4)  
Press CDU ENT pushbutton, display changes to show DATA BASE VALID or DATA BASE EXPIRE.

IF -

EFFECTIVITY
CONFIG 3 AIRPLANES WITH LTN-72RL OR
799 Page 107 LTN-92 INS
Apr 25/91
34-41-00

EFFECTIVITY
CONFIG 3 AIRPLANES WITH LTN-72RL OR
799 Page 108 LTN-92 INS
 Apr 25/91
34-41-00

NOT OK
OK

NOT OK
OK
LAT OR LON LINES CONTINUE TO FLASH -PROCEDURE 1

A. Check alignment status as follows:
(1)  
Ensure present position coordinates are entered into INS.

(2)  
Place the MSU mode selector switch to ALIGN.

(3)  
Press CDU STS pushbutton; SYS STS/TEST page appears on CDU display.

(4)  
Observe that number on ALIGN line is status number, and number on TIME line is minutes and tenths of minutes remaining to READY NAV time. Status numbers start at 90 and decrement through 80,70,60,50,10, and 2 as alignment sequence progresses.

NOTE:On airplanes with LTN-72RL INS, The ALIGN annunciator goes out at status 2. Also, alignment status 40 will be displayed during alignment sequence.

(5)  
Because the mode switch is set to ALIGN, READY NAV annunciator comes on at status 2. The mode switch may be set to NAV, the READY NAV annunciator then goes out and the ALIGN line changes to NAV with a status number of 1. The TIME line changes to time in navigation mode.

IF -

INS WRN ANNUNCIATOR FLASHES OR COMES ON STEADY DURING
ALIGNMENT SEQUENCE -

On airplanes with LTN-92 INS,
check for Malfunction and Action messages. Perform
recommended action shown on CDU display.

On airplanes with LTN-72RL INS,
check for Malfunction and Action codes as described in
previous 'Action and Malfunction Code' paragraph. Per-form recommended action shown on CDU display (Ref
Fig. 101).

EFFECTIVITY
CONFIG 3 AIRPLANES WITH LTN-72RL OR
799 Page 109 LTN-92 INS
 Apr 25/91
34-41-00
OK

A. Perform VORTAC position update as follows:
(1)  
Verify that MSU mode selector switch is in NAV.

(2)  
Press AUTO switch/indicator on VHF navigation control panel and verify that the indicator illuminates.

(3)  
Observe frequency display on VHF navigation control panel; verify that the VOR system is tuned to the closest VORTAC station.

(4)  
Press the CDU STS pushbutton, SYS STS/TEST page appears on CDU display. Slew display to place UPDATE between entry line marker. Observe display automatically changes to UDT MODE: INS page with CHANGE UDT MODE between entry line markers.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747飛機維護手冊AMM CHAPTER 34 - NAVIGATION 第34章導航3(17)