34-41-00
 f)  On airplanes with INS program 72-50-01, program 72-50-01 is displayed as 72 in left display and 50 01 in right display.
 g)  On airplanes with INS program 72-50-02, program number 72-50-02 is displayed as 72 in left display and 50-02 in right display.
 h)  On airplanes with INS program 72-50-03, program number 72-50-03 is displayed as 72 in left display and 50 03 in right display.
 i)  On airplanes with INS program 72-50-04, program number 72-50-04 is displayed as 72 in left display and 50 04 in right display.
 (c) Insert correct present position data in each INS.
 NOTE: Automatic alignment of INS cannot be completed until
____ this data is inserted separately into each INS through the individual control display units.
 1)  Place data selector to POS and press N2 or S8 key for north or south present position latitude. Check that left numerical display blanks, N or S appears in left-hand data display and INSERT pushbutton illuminates.
 2)  Press numbered keys in sequence for present position latitude and observe that correct latitude appears in left-hand data display.
 NOTE: Numbers shift to left in display as each additional
____ number is loaded. If incorrect data is displayed, press CLEAR key and repeat steps 1) and 2).
 3)  Press INSERT key and observe that INSERT key light remains illuminated.
 4)  Press W4 or E6 key for west or east present position longitude and observe that 000.00.0 followed by correct letter (W or E) appears in right-hand data display.
 5)  Press numbered keys in sequence for present position longitude and observe that correct longitude appears in right-hand data display.
 NOTE: If incorrect data is displayed, press CLEAR key and
____ repeat steps 4) and 5).
 6)  Press INSERT key. Observe that INSERT key light extinguishes and that correct present position data within 0.2 minute is displayed in both left-hand and right-hand displays.
 (d)  Place data selector to DSR TK/STS and observe that status 80 is displayed in right-hand display.
 EFFECTIVITY
 AIRPLANES WITH LTN-72 INS   
  CONFIG  01 A Page 511  Aug 25/87

34-41-00
 (e)  Place MSU mode selector switch to ALIGN and check that status 70 is displayed in right-hand display. Note and record time.
 (f) Waypoint coordinate entry. 1) On each CDU, place data selectors to WPT and WPT switches to 1. 2) On any one control/display unit, perform following: a) Press N2 or S8 key for north or south first waypoint latitude. Observe that INSERT key illuminates and that 00.00.0 followed by correct letter (N or S) appears in left-hand data display.
 b)  Press numbered keys in sequence for first waypoint latitude and observe that correct latitude appears in left-hand data display.
 NOTE: If incorrect data is displayed, press CLEAR
____ key, observe that INSERT key light goes out, and repeat steps a) and b).
 c)  Press INSERT key. Observe that INSERT key light extinguishes and that correct data (within 0.2 minute) is still displayed in left-hand data display.
 d)  Press W4 or E6 key for west or east waypoint longitude. Observe that INSERT key illuminates and that 000.00.0 followed by correct letter (W or E) appears in right-hand data display.
 e)  Press numbered keys in sequence for first waypoint longitude and observe that correct longitude appears in right-hand data display.
 NOTE: If incorrect data is displayed, press CLEAR
____ key, observe that INSERT key light goes out, and repeat steps d) and e).
 f)  Press INSERT key. Observe that INSERT key light extinguishes and that correct data (within 0.2 minute) is still displayed in right hand data display.
 3)  Repeat steps 1) and 2) for additional waypoint insertions. Set WPT switch to position 2 up to 9 consecutively while entering each successive waypoint.
 (g)  Autofill Procedures, Waypoint Coordinate Entry. 1) On each control display unit place the data selectors to WPT.
 2)  On CDU No. 1 place the AUTO/MAN/RMT switch to RMT. On CDU No. 2 and No. 3 place the AUTO/MAN/RMT switches to MAN.
 EFFECTIVITY AIRPLANES WITH LTN-72 INS  
  CONFIG  01 A Page 512  Aug 25/87

34-41-00
 3)
4)
5) 6)
7)
8)
Enter the following waypoint coordinate data into the INS using CDU No. 1 and the procedures of par (f) (waypoint coordinate entry). When entering the data ensure the WPT switch is set to the appropriate number.
 Waypoint 1.  N48.00.0  W122.16.8
 Waypoint 2.  N20.00.0  W120.00.0
 Waypoint 3.  N30.00.0  W130.00.0