4.
On one of the ACPs, push the RESET pushbutton switch and release it.
-
The frequency set comes into view inthe ACTIVE display window.
-
The green bars on the VHF1 (VHF2,VHF3) transmission pushbutton switch come on.
-
The reception pushbutton switch movesfully out and comes on.
-On each ACP, the amber CALL legend ofthe VHF1 (VHF2, VHF3) transmission pushbutton switch flashes.
-You can hear the buzzer.
-On all ACPs, the amber CALL legend ofthe VHF1 (VHF2, VHF3) transmissionpushbutton switch goes off.
-The buzzer stops.
R 1EFF : 106-149, 211-299, 1 23-51-00Page 515 1 1 May 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
5. On the RMP1:
-Push the HF1 pushbutton switch
-In the STBY/CRS display window, with the dual selector knob, set the frequency that the ground station can use in HF.
-Start this frequency. To do this, push the transfer pushbutton switch (double arrow) between the two display windows.
6. On the CAPT ACP:
-
Push the HF1 transmission
pushbutton switch.
-
Push and release the VHF1
(VHF2, VHF3) reception
pushbutton switch.
-
Push and release the HF1 reception pushbutton switch.
-
Push the PTT switch of the CAPT sidestick controller.
The SEL indicator light (white LED)
comes on.
On the RMP1:
-
The green LED on the VHF1 pushbutton switch goes off.
-
The green LED on the HF1 pushbutton switch comes on.
-
The frequency set comes into view, inthe ACTIVE display window.
-
The green bars on the VHF1 (VHF2,VHF3) transmission pushbutton switch go off.
-
The green bars on the HF1 transmission pushbutton switch come on.
-This pushbutton switch moves in (tothe initial position) and theannunciator light goes off.
-The reception pusbutton switch movesfully out and comes on.
-During the tuning (which continuesfor approximately 5 seconds), the reception stops and you can hear a signal of 1000 Hz in the boomset.
R 1EFF : 106-149, 211-299, 1 23-51-00Page 516 1 1 May 01/05 1 1 1CES 1
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
-Tell the ground station to make
a SELCAL call on the HF1
system.
-Release the PTT switch of the - On each ACP, the amber CALL legend of
CAPT sidestick controller. the HF1 transmission pushbutton switch flashes.
-You can hear the buzzer.
7. On one of the ACPs, push the - On all ACPs, the amber CALL legend of RESET pushbutton switch and the HF1 transmission pushbutton release it. switch goes off.
-The buzzer stops.
**ON A/C ALL
5. Close-up
________
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-210, 301-399, 401-499,
Subtask 23-51-00-860-053
A. Put the aircraft back to its initial configuration.
(1)
On the RMPs, set the ON/OFF selector switch to OFF.
(2)
On the ACP, push the HF1 (HF2) transmission pushbutton switch and the HF1 (HF2) reception pushbutton switch.
(3)
At the Captain station, disconnect the boomset.
(4)
De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).
1EFF : ALL 1 23-51-00Page 517 1 1 Aug 01/05 1 1 1CES 1R **ON A/C 106-149, 211-299,
Subtask 23-51-00-860-053-A
A. Put the aircraft back to its initial configuration.
(1)
On the RMPs, set the ON/OFF selector switch to OFF.
(2)
On the ACP, push the HF1 transmission pushbutton switch and the HF1 reception pushbutton switch.
(3)
At the Captain station, disconnect the boomset.
(4)
De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).
R 1EFF : 106-149, 211-299, 1 23-51-00Page 518 1 1 May 01/05 1 1 1CES 1 **ON A/C ALL
TASK 23-51-00-710-003
R Operational Test of the CAPT and F/O ACPs Switching to the 3rd OCCUPANT ACP WARNING : MAKE SURE THAT ALL THE CIRCUITS IN MAINTENANCE ARE ISOLATED BEFORE
_______
YOU SUPPLY ELECTRICAL POWER TO THE AIRCRAFT.
NOTE : You can do this test in the hangar.
____
1. Reason for the Job
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM Communications 通訊2(134)
