-touch the PFIS indication,
-push the EXEC pushbutton
switch.
4. On the PVIS RCU:
-
push the pushbutton switch SET again.
-
push the pushbutton switch UP or DOWN to set the cursor to the MAP MODE.
-
push the pushbutton switch SET.
-the message PROCEEDING SELF TEST ---comes into view.
In the cabin:
-all Hatrack Mounted Display Units (HMDU) 100MH move down out of the hatrack and after 5s retract into the hatrack.
On the monitor of the SCU 11MH:
-
the MENU page comes into view,
-
the zone marks are blinking.
In the cabin:
-the HMDU move down out of the hatrack.
In the cabin on the HMDU:
-no flight information or maps areshown.
-
the LOGO available is shown.
-
the maps are shown.
1EFF : 051-099, 1 23-34-00Page 503 1 1 May 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
- push the pushbutton switch UP - no maps are shown.
or DOWN to set the cursor to - no flight information is shown.
the INFO MODE.
- push the pushbutton switch SET.
- push the pushbutton switch UP - the LOGO available is shown.
or DOWN to set the cursor to
the LOGO MODE.
- push the pushbutton switch SET.
5. On the circuit breaker panel On the PVIS RCU:
2000VU:
- open, safety and tag - the PVIS with all indications
this(these) circuit breaker(s): switches off.
189MH.
Subtask 23-34-00-710-051
B. Test of the Passenger Visual Information System (PVIS)
(1) Do this test (with the data from the FMGC and the ADIRS):
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the circuit breaker panel 121VU:
-remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 10CA2 6FP2 4FP2 5FP2
2. On the circuit breaker panel 2000VU:
-remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 189MH.
On the LCD of the PVIS RCU:
-STANDBY is indicated for theinitialization and self-test period.
-the cursor is set to SET DISPLAY MODEafter the self-test is complete.
1EFF : 051-099, 1 23-34-00Page 504 1 1 May 01/05 1 1 1CES 1
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
3.
Do the Check of the IR Alignment Procedure (Ref. TASK 34-10-00-860-004).
4.
On the PVIS RCU:
-
push the pushbutton switch SET.
-
push the SET again.
-
push the pushbutton switch UP or DOWN to set the cursor to the MAP MODE.
-
push the pushbutton switch SET.
-
push the pushbutton switch UP or DOWN to set the cursor to the INFO MODE.
-
push the pushbutton switch SET.
-
push the pushbutton switch UP or DOWN to set the cursor to the LOGO MODE.
-
push the pushbutton switch SET.
5.
On the SCU 11MH:
-push the SYST PWR pushbutton switch.
On the LCD of the RCU:
-
the cursor moves to the AUTO MODE menu.
In the cabin on the HMDU:
-
the LOGO available is shown.
-
the flight information is shown.
-
the maps are shown.
-
the maps are shown.
-
the flight information is shown.
-
the LOGO available is shown.
In the cabin:
-all HMDU go off and retract into thehatracks.
On the SCU 11MH:
-
the monitor goes off,
-
the intregral light of the SYST PWR pushbutton switch goes off.
1EFF : 051-099, 1 23-34-00Page 505 1 1 May 01/05 1 1 1CES 1
5. Close-up
________ Subtask 23-34-00-860-053
A. Put the aircraft back to its initial configuration.
(1)
On the panels 301VU and 500VU, set the PFD and ND potentiometers to OFF.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM Communications 通訊2(27)
