-------------------------------------------------------------------------------ACTION RESULT
-------------------------------------------------------------------------------ATA 23-73-14 TEST OK.
5. Close-up
________
Subtask 23-73-14-862-055
A. De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).
R 1EFF : 001-049, 051-099, 101-105, 151-154, 1 23-73-14Page 419 1201-207, 1May 01/05 1 1 1CES 1
PROGRAMMING AND TEST PANEL (110RH) - REMOVAL/INSTALLATION
_________________________________________________________ TASK 23-73-18-000-001 Removal of the Programming and Test Panel 110RH
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
23-73-19-000-001 Removal of the Cabin Assignment Module (115RH) 24-42-00-861-001 Energize the Ground Service Network from the External Power 31-32-00-860-003 Procedure to Get Access to the SYSTEM REPORT/TEST/COM Page 23-73-18-991-001 Fig. 401
3. Job Set-up
__________ Subtask 23-73-18-970-050
A. Access to the Trouble Shooting Data
(1) If required, print the Trouble Shooting Data (TSD) as follows:
(a)
Get access to the (Ref. TASK 31-32-00-860-003)
(b)
Print the Trouble Shooting Data (TSD).
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 23-73-18Page 401 1201-299, 1May 01/05 1 1 1CES 1 Subtask 23-73-18-861-050
B. Energize the ground service network
(Ref. TASK 24-42-00-861-001)
Subtask 23-73-18-865-050
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
R **ON A/C 001-049, 051-099, 101-105, 201-299,
121VU COM NAV/CIDS/PROG AND TST PNL 161RH M06 **ON A/C 151-199,
121VU COM NAV/CIDS/PROG &/TST PNL 161RH M07 R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-299,
4. Procedure
_________
(Ref. Fig. 401/TASK 23-73-18-991-001)
Subtask 23-73-18-020-050
A. Removal of the programming and test panel
(1)
Open the access door (10).
(2)
Remove the Cabin Assignment Module (Ref. TASK 23-73-19-000-001).
(3)
Remove the screws (7), the washers (8) and the cover (9).
(4)
Remove the screws (5) and the washers (6).
(5)
Pull and lower the programming and test panel (1) with the brackets
(2) until you can see the electrical connector (11).
(6)
Disconnect the electrical connector (11) from the programming and test panel (1).
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 23-73-18Page 402 1201-299, 1May 01/05 1 1 1CES 1
Programming and Test Panel
Figure 401/TASK 23-73-18-991-001
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 23-73-18Page 403 1201-299, 1May 01/05 1 1 1CES 1
(7)
Remove the screws (3), the washers (4) and the brackets (2) from the
programming and test panel (1).
(8)
Remove the programming and test panel (1).
(9)
Put blanking caps on the disconnected electrical connectors.
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 23-73-18Page 404 1201-299, 1May 01/05 1 1 1CES 1
TASK 23-73-18-400-001 Installation of the Programming and Test Panel 110RH
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
23-73-00-740-005 BITE Test of the Cabin Intercommunication Data System
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM Communications 通訊4(105)
