曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 2. Job Set-up Information______________________
 A. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R R  23-73-00-740-003 23-73-00-740-010 23-73-00-869-001 23-73-34-000-001 23-73-34-400-001 26-16-00-710-001 26-17-00-710-001 52-41-00-410-002  BITE Test of the Cabin Intercommunication Data System (CIDS) through the PTPInterface and Power-Up Test of the Cabin Intercommunication Data System (CIDS) via the CFDS OBRM - Download ProcedureRemoval of the CIDS Director (101RH,102RH)Installation of the CIDS Director (101RH,102RH) Operational Check of Cargo-Compartment Smoke-Detection by PTTOperational Test of the Lavatory Smoke-Detection SystemClose the Avionics Compartment Doors after Access

 1EFF : ALL 1 23-73-34Page 406 1 1 Feb 01/05 1 1 1CES 1

 3. Job Set-up
__________
 Subtask 23-73-34-865-051

 A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 101RH
 **ON A/C 001-049, 051-099, 101-105, 201-299,
 49VU COM/CIDS/DIR 1 AND 2/ESS 150RH G02 R **ON A/C 106-149, 301-399, 401-499,
 49VU AIR COND/CIDS/SDF/DIR1 ESS 15WH C05 R **ON A/C 106-149, 151-199, 301-399, 401-499,
 49VU COM DIR ESS/1 150RH G01 **ON A/C 001-049, 051-099, 101-105, 151-199, 201-299,
 121VU COM NAV/CIDS/DIR 1 AND 2/NORM 151RH M05 **ON A/C 301-399,
 121VU COM NAV/CIDS/DIR NORM/1 151RH M06 R **ON A/C 106-149, 301-399, 401-499,
 122VU AIR COND/CIDS/SDF/DIR NORM/1 17WH T17 **ON A/C ALL
 FOR 102RH
 1EFF : ALL 1 23-73-34Page 407 1 1 Aug 01/05 1 1 1CES 1

 -------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------**ON A/C 001-049, 051-099, 101-105, 201-299,
R  49VU COM/CIDS/DIR 1 AND 2/ESS **ON A/C 106-149, 301-399, 401-499, 150RH  G02 
R  49VU AIR COND/CIDS/SDF/DIR2 ESS **ON A/C 106-149, 401-499, 18WH  C06 
R  49VU COM/CIDS/DIR ESS/2 **ON A/C 106-149, 151-199, 301-399, 401-499, 157RH  G02 
49VU COM DIR ESS/1 **ON A/C 151-199, 301-399, 150RH  G01
 49VU COM DIR ESS/2 **ON A/C 001-049, 051-099, 101-105, 151-199, 201-299, 157RH  G02
R  121VU COM NAV/CIDS/DIR 1 AND 2/NORM **ON A/C 106-149, 151-199, 401-499, 151RH  M05 
121VU COM NAV/CIDS/DIR NORM/2 **ON A/C 301-399, 156RH  M06
 121VU COM NAV/CIDS/DIR NORM/2 121VU COM NAV/CIDS/DIR NORM/1  156RH 151RH  M07M06

 1EFF : ALL 1 23-73-34Page 408 1 1 Aug 01/05 1 1 1CES 1 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------

 

R **ON A/C 106-149, 301-399, 401-499,
 122VU AIR COND/CIDS/SDF/DIR NORM/2 14WH T18 **ON A/C ALL
 4. Procedure
_________
 **ON A/C 001-049, 051-099, 101-105, 201-299,

 Subtask 23-73-34-420-050
 A. Installation of the CIDS Directors NOTE : The installation procedures of the two CIDS Directors are not the
____
 same.

 (1)
 Installation of the CIDS Director 1

 (a)
 Clean the component interface and/or the adjacent area.

 (b)
 Do an inspection of the component interface and/or the adjacent area.

 (c)
 Remove the blanking caps from the electrical connectors (1).

 (d)
 Make sure that the electrical connectors (1) are clean and in the correct condition.

 (e)
 Install the CIDS director 1(5) on its rack (2).

 (f)
 Push the CIDS director 1(5) on its rack (2) to connect the electrical connectors (1).

 (g)
 Engage the nuts (3) on the lugs (4) and tighten.

 

 (2)
 Installation of the CIDS Director 2

 (a)
 Remove the CIDS Director 1 (101RH) (Ref. TASK 23-73-34-000-001).

 (b)
 Clean the component interface and/or the adjacent area.

 

 1EFF : ALL 1 23-73-34Page 409 1 1 Aug 01/05 1 1 1CES 1

 (c)
 Do an inspection of the component interface and/or the adjacent area.

 (d)
 Remove the blanking caps from the electrical connectors (1).

 (e)
 Make sure that the electrical connectors (1) are clean and in the correct condition.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM Communications 通訊4(114)