(4)
Put the bonding strip (6) on the cartridge (7) and install a new O-ring (30).
(5)
Install the cartridge (7) on the discharge head (5).
(a)
TORQUE the cartridge (7) to between 90 and 100 lbf.in (1.01 and
1.13 m.daN).
(b)
Safety the cartridge (7) with corrosion-resistant steel lockwire dia. 0.8 mm (0.030 in).
(6)
Remove the SHUNT PLUG - FIRE EXTINGUISHER CARTRIDGE, HTL (10-101950-81) from the cartridges (7) and (14).
(7)
Remove the blanking cap from the electrical connector (15).
(a)
Make sure that the electrical connectors are clean and in the correct condition.
(b)
Connect the electrical connector (15) to the cartridge (14).
R 1EFF : 004-049, 051-099, 101-149, 151-199, 1 26-23-41Page 414 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(8) Remove the blanking cap from the electrical connector (8).
(a) Make sure that the electrical connectors are clean and in the correct condition.
(b) Connect the electrical connector (8) to the cartridge (7). **ON A/C 301-399,
Subtask 26-23-41-420-055-A
A. Installation of the Cartridges
(1)
Remove the blanking plugs from the discharge heads (5) and (12).
(2)
Put the bonding strip (13) and install a new O-ring (30) on the cartridge (14).
(3)
Install the cartridge (14) on the discharge head (12).
(a)
TORQUE the cartridge (14) to between 90 and 100 lbf.in (1.01 and
1.13 m.daN).
(b)
Safety the cartridge (14) with corrosion-resistant steel lockwire dia. 0.8 mm (0.030 in).
(4)
Put the bonding strip (6) and install a new O-ring (30) on the cartridge (7).
(5)
Install the cartridge (7) on the discharge head (5).
(a)
TORQUE the cartridge (7) to between 90 and 100 lbf.in (1.01 and
1.13 m.daN).
(b)
Safety the cartridge (7) with corrosion-resistant steel lockwire dia. 0.8 mm (0.030 in).
(6)
Remove the PROTECTIVE CAP - FIRE EXTINGUISHER CARTRIDGE (861823) from the cartridges (7) and (14).
(7)
Remove the blanking cap from the electrical connector (15).
(a)
Make sure that the electrical connectors are clean and in the correct condition.
(b)
Connect the electrical connector (15) to the cartridge (14).
R 1EFF : 004-049, 051-099, 101-149, 151-199, 1 26-23-41Page 415 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(8) Remove the blanking cap from the electrical connector (8).
(a) Make sure that the electrical connectors are clean and in the correct condition.
(b) Connect the electrical connector (8) to the cartridge (7). R **ON A/C 004-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 26-23-41-865-059
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1WX, 8WX.
Subtask 26-23-41-710-052
C. Do an operational test of the fire extinguisher bottle of the cargo compartment section (Ref. TASK 26-23-00-710-001).
5. Close-up
________
**ON A/C 004-049, 051-099, 101-149, 201-299, 301-399,
Subtask 26-23-41-410-053
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the protection panel 132MW.
(3)
Set the CARGO COMPT LIGHT switch 6LU to the OFF position.
(4)
Close the forward cargo compartment door 825 (Ref. TASK 52-30-00-860-002).
(5)
Remove the access platform(s).
R 1EFF : 004-049, 051-099, 101-149, 151-199, 1 26-23-41Page 416 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1R **ON A/C 151-199, 401-499,
Subtask 26-23-41-410-053-A
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the protection panel 132SW.
(3)
Set the CARGO COMPT LIGHT switch 6LU to the OFF position.
(4)
Close the forward cargo compartment door 825 (Ref. TASK 52-30-00-860-002).
(5) Remove the access platform(s). R **ON A/C 004-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 26-23-41-862-052
B. De-energize the ground service network (Ref. TASK 24-42-00-862-001).
R 1EFF : 004-049, 051-099, 101-149, 151-199, 1 26-23-41Page 417 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FIRE PROTECTION 防火2(104)
