4. Procedure
_________
**ON A/C 001-001, 051-052,
(Ref. Fig. 401/TASK 28-42-16-991-001) R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499, Post SB 28-1077 For A/C 001-001,051-052, (Ref. Fig. 401A/TASK 28-42-16-991-001-A) R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 28-42-16-420-052
A. Preparation for Installation
(1)
Clean the component interface and the adjacent areas with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Make sure that the parts retained from the removed component are clean and in the correct condition.
Subtask 28-42-16-560-050
B. Preparation of a Replacement Component
(Ref. Fig. 402/TASK 28-42-16-991-003)
(1) Remove the transport pin (10) from the cadensicon (1) if installed. NOTE : The transport pin (10) is only installed on cadensicon part
____ number 796-809-6A. Cadensicon part numbers 796-809-5 and 796-809-6 do not have a transport pin installed.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-42-16Page 410 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
Cadensicon Transport Pin
Figure 402/TASK 28-42-16-991-003
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-42-16Page 411 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
**ON A/C 001-001, 051-052,
Subtask 28-42-16-420-050
C. Installation of the Cadensicon
(Ref. Fig. 401/TASK 28-42-16-991-001)
(1)
Install the cadensicon (1) on the support bracket (3) with the bolts (2).
(2)
Apply a layer of SEALANTS (Material No. 09-007) to the two ends of the bolts (2).
CAUTION : REFER TO THE MATCH MARKS MADE DURING THE REMOVAL WHEN YOU
_______ CONNECT THE ELECTRICAL WIRES. INCORRECT CONNECTION OF THE WIRES WILL CAUSE DAMAGE TO EQUIPMENT.
(3) Remove the blanking caps and connect the electrical connectors (4) to the cadensicon (1). R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Post SB 28-1077 For A/C 001-001,051-052,
Subtask 28-42-16-420-050-A
C. Installation of the Cadensicon
(Ref. Fig. 401A/TASK 28-42-16-991-001-A)
NOTE : You must bond the mating surfaces of the cadensicon (1) (Ref. TASK
____
28-42-16-991-001) (Ref. TASK 20-28-00-912-043).
(1)
Install the cadensicon (1) on the support bracket (3) with the bolts (2).
(2)
Apply a layer of SEALANTS (Material No. 09-007) to the two ends of the bolts (2).
CAUTION : REFER TO THE MATCH MARKS MADE DURING THE REMOVAL WHEN YOU
_______ CONNECT THE ELECTRICAL WIRES. INCORRECT CONNECTION OF THE WIRES WILL CAUSE DAMAGE TO EQUIPMENT.
(3) Remove the blanking caps and connect the electrical connectors (4) to the cadensicon (1).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-42-16Page 412 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 28-42-16-410-050
D. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the wing access panel (Ref. TASK 57-27-11-400-001):
-
FOR 19QT1
install 540AB
-
FOR 19QT2
install 640AB.
Subtask 28-42-16-650-054
E. Fuel Configuration
(1) Refuel, defuel or transfer fuel as necessary (Ref. TASK 12-11-28-650-003), (Ref. TASK 28-25-00-650-001) or (Ref. TASK 28-25-00-869-001).
Subtask 28-42-16-865-051
F. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1QT, 2QT, 8QT, 1QU, 2QU.
Subtask 28-42-16-740-050
G. Test
(1) Do a STATUS REPORT (BITE) test on the Fuel Quantity Indicating System (Ref. TASK 28-42-00-740-001).
5. Close-up
________
Subtask 28-42-16-942-050
A. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safety barriers.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-42-16Page 413 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(3)
Remove the warning notice(s).
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUEL 燃油5(74)
