-
the fuel sensors 15QJ1(15QJ2), 23QJ1(23QJ2) and 24QJ1(24QJ2).
(b)
Disconnect the terminal connectors (2) from the terminal block of the fuel probes 22QT1(22QT2), 24QT1(24QT2) and 26QT1(26QT2).
(c)
Remove and discard the terminal connectors (2) from the ends of the harness 14QT1(14QT2).
(d)
Loosen the clamp screws (21), the connector screws (20) and remove the cables from the sensors 15QJ1(15QJ2), 23QJ1(23QJ2) and 24QJ1(24QJ2).
(e)
Remove and discard the cable-ties (1) from the harness 14QT1(14QT2) and the fuel probes 22QT1(22QT2), 24QT1(24QT2) and 26QT1(26QT2).
(f)
Remove and keep the nylon spacers (5).
(g)
Remove the bolt (4) to release the P clip (3).
(h)
Remove the harness 14QT1(14QT2) from the P clip (3) and use the bolt (4) to temporarily install the P clip (3).
(i)
Loosen the clamp screws (21), the connector screws (20) and remove the cable from the sensor 39QJ1(39QJ2).
(j)
Remove and discard the cable-ties (1) from the harness 14QT1(14QT2).
R 1EFF : 106-149, 229-299, 401-499, 1 28-42-43Page 450 1 1 Aug 01/05 1 1 1CES 1
(2) Remove the harness 14QT1 (14QT2) at RIB 7 as follows: (Ref. Fig. 402/TASK 28-42-43-991-004, 404/TASK 28-42-43-991-007, 405/TASK 28-42-43-991-009)
WARNING : CUT, REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE TASK.
_______
LOOSE LOCKWIRE CAN CUT OR BLIND YOU.
(a)
Get access through the opening 574BB(674BB).
(b)
Disconnect the plug connector (33) from the connector
4040VC1(4040VC2) (34).
(c)
Put a blanking cap on the plug connector (33).
(d)
Remove and discard the lockwire from the nut (32).
(e)
Remove the nut (32) and the washer (31) from the connector (34).
(f)
Get access through the opening 540BB(640BB) to the rear spar.
(g)
Use a plastic spatula to remove the sealant from between the connector (34) and the tank wall.
(h)
Remove the connector (34) and discard the O-ring (30).
(i)
Remove and discard the lockwire and loosen the clamp screws (36).
(j)
Remove and discard the lockwire from the backshell connector (35).
(k)
Remove the backshell connector (35) from the connector (34).
(l)
Keep the backshell connector (35) and the connector (34).
(m)
Remove the bolt (4) from the P clip (3), then remove and keep the P clip (3).
(n)
Disconnect the terminal connectors (2) from the fuel probe 28QT1(28QT2).
(o)
Remove and discard the terminal connectors (2) from the terminal block of the harness 14QT1(14QT2).
(p)
Remove and discard the cable-ties (1) from the harness
14QT1(14QT2) and the fuel probe 28QT1(28QT2) body.
R 1EFF : 106-149, 229-299, 401-499, 1 28-42-43Page 451 1 1 Aug 01/05 1 1 1CES 1
(3)
Remove the harness 14QT1 (14QT2) at RIB 9 as follows: (Ref. Fig. 406/TASK 28-42-43-991-011)
(a)
Get access through the opening 540CB(640CB).
(b)
Loosen the clamp scew (21), the connector screws (20) and remove the cable from the sensor 25QJ1(25QJ2).
(c)
Remove and discard the cable-ties (1) from the harness
14QT1(14QT2).
(4)
Remove the harness 14QT1 (14QT2) at RIB 11 as follows: (Ref. Fig. 402/TASK 28-42-43-991-004, 407/TASK 28-42-43-991-010)
(a)
Get access through the opening 540FB(640FB).
(b)
Disconnect the terminal connectors (2) from the terminal block of the fuel probe 30QT1(30QT2).
(c)
Remove and discard the terminal connectors (2) from the harness 14QT1(14QT2).
(d)
Remove and discard the cable-ties (1) from the harness
14QT1(14QT2).
(5)
Remove the harness 14QT1 (14QT2) at RIB 13 as follows: (Ref. Fig. 402/TASK 28-42-43-991-004, 404/TASK 28-42-43-991-007, 405/TASK 28-42-43-991-009, 407/TASK 28-42-43-991-010)
(a)
Get access through the opening 540GB(640GB).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUEL 燃油5(98)
