5. Close-up
________ Subtask 51-23-00-865-051
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 5CC1, 5CC2, 14CC1, 14CC2, 15CC, 15CE1, 15CE2, 16CE1, 16CE2, 19CE1, 19CE2, 19CE3, 22CE, 21CE1, 21CE2, 21CE3
Subtask 51-23-00-410-050
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the access platform(s).
(3)
Remove the warning notice(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 51-23-00Page 239 1 1 May 01/04R 1 1 1CES 1
TASK 51-23-00-370-006
Application of Paint and Protective Coatings - Pylon and Nacelle Areas
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL MATERIALS
_______ ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
WARNING : DO NOT GET THE COMPOUND ON YOUR SKIN.
_______ IF YOU DO:
-RUB IT OFF IMMEDIATELY WITH A CLEAN CLOTH
-WASH THE SKIN WITH SOAP AND RINSE WITH CLEAN WATER.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific 1 ACCESS PLATFORM 1M (3 FT) No specific 1 ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE No specific 1 WARNING NOTICE
1EFF : ALL 1 51-23-00Page 240 1 1 May 01/04R 1 1 1CES 1
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 07-005 C Z-12.506
ANTISTATIC PAINT (LOW RESISTIVITY) (Ref. 20-31-00) Material No. 08-008 D DA4-653-83
POLYESTER FILLER (Ref. 20-31-00) Material No. 16-001
ANTI-CORROSION PRIMER (POLYURETHANE ) (Ref. 20-31-00) Material No. 16-006
ANTI-CORROSION PRIMER (EPOXY-IMPRVD ADHESION)
(Ref. 20-31-00) Material No. 16-018
EXTERNAL TOP COAT (POLYURETHANE) (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
51-23-00-991-007 Fig. 207
3. Job Set-up
__________
Subtask 51-23-00-860-055
A. Aircraft Maintenance Configuration
(1)
Put a WARNING NOTICE in position to tell persons not to start the engine: - on the panel 115VU in the cockpit.
(2)
Make sure that the engine 1(2) has been shutdown for a minimum of five minutes before you do these subsequent procedures:
-
Application of the Protective Coatings
-
Application of the Paint.
(3)
Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(4)
Put a WARNING NOTICE in position to tell persons not to energize the FADEC 1(2): - on the panel 50VU in the cockpit.
1EFF : ALL 1 51-23-00Page 241 1 1 May 01/04R 1 1 1CES 1
Subtask 51-23-00-010-054
B. Get Access
(1) Pylons
(a) Put a ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in postion: - at zone 470 for the left pylon - at zone 480 for the right pylon.
(2) Nacelles
(a) Put a ACCESS PLATFORM 1M (3 FT) in postion: - at zone 470 for the left nacelle - at zone 480 for the right nacelle.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM STANDARD PRACTICES AND STRUCTURES(18)
