R (12) Rub the roughened area with abrasive paper grade 400. Rub along the
R length of the scratch until the surface is smooth.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE_______
SPECIAL MATERIAL.
THIS MATERIAL IS DANGEROUS.
R
R (13) Clean the area with CLEANING AGENTS (Material No. 11-004) and a lint-
free cloth.
R
R (14) Polish the bare metal with SPECIAL MATERIALS (Material No. 05-025)
R and a lint-free cloth:
NOTE : Rub the area in the direction of the scratch. Do not rub with____
a circular motion. Make sure you remove all the rough surface.
R
R (15) Clean the area with CLEANING AGENTS (Material No. 11-004) and a clean
R cloth.
R
R (16) Apply PRETREATMENT FOR PAINTING (Material No. 13-002) to the metal
R surface.
R
R (17) Apply the applicable surface protection (Ref. TASK 51-75-12-300-001).
5. Close-up________
Subtask 51-73-11-942-051
A. Remove the ground support and maintenance equipment, the special and
standard tools and all other items.
TASK 51-73-11-300-004
Repair of Minor Damage on Unclad Components
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL MATERIALS
_______ ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific abrasive cloth grade 280 No specific abrasive paper grade 400 No specific lint free cloth No specific lint-free cloth No specific rounded scotch stone
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 05-025 USA MIL-P-6888 POLISH METAL ALUMINUM (Ref. 20-31-00)
Material No. 11-004 USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
Material No. 13-002 USA MIL-C-5541 MIL-C-81706 CLASS I/A CHEMICAL CONVERSION COATING YELLOW ALUMINUM (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
51-74-11-300-001 51-75-12-300-001 Repair of Corroded AreasRepair of Major Paint Damage on Light Alloy and Composite Material
3. Job Set-up__________
Subtask 51-73-11-941-052
A. Get access to the area of the damage.
4. Procedure_________
Subtask 51-73-11-320-054
A. Repair of Minor Damage
R (1) If necessary, remove any corrosion (Ref. TASK 51-74-11-300-001).
R (2) Measure the depth of the scratch.
R R (3) Refer to the ASRM 51-73-00 and the applicable ASRM-chapter 52 thru 57 for the permitted depth limits.
R R (4) Remove the paint from the area of the scratch with abrasive cloth grade 280 until you can see all of the scratch.
(5) Clean the repair area with CLEANING AGENTS (Material No. 11-004) and a lint free cloth.
(6) Remove the scratch with a rounded scotch stone and water. Move the scotch stone along the scratch until the contour is smooth and rounded.
(7) Rub the roughened area with abrasive paper grade 400. Rub along the length of the scratch until the surface is smooth.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE_______ SPECIAL MATERIAL. THIS MATERIAL IS DANGEROUS.
(8)
Clean the area with CLEANING AGENTS (Material No. 11-004) and a lint-
free cloth.
(9)
Polish the bare metal with SPECIAL MATERIALS (Material No. 05-025) and a lint-free cloth:
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM STANDARD PRACTICES AND STRUCTURES(22)
