R B. If the test confirms the fault:
R - replace the GCU-2 (1XU2) (Ref. AMM TASK 24-22-34-000-001) and (Ref. AMM
R TASK 24-22-34-400-001).
R (1) If the fault continues:
R - replace the engine 2 IDG (4000XU) (Ref. AMM TASK 24-21-51-000-040)
R and (Ref. AMM TASK 24-21-51-400-040).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞24-22-00∞∞∞∞∞∞∞∞∞∞Page 218
Aug 01/05 CES
R (2) If the fault continues:
R - do a check and repair the wiring between the pins A/9, A/10 of the
R engine 2 IDG (4000XU) and the pins C/12, C/13 of the GCU 2 (1XU2)
R (Ref. ASM 24-22/01).
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
C. If the test confirms the fault:
- replace the EGIU-2 (22XU2) (Ref. AMM TASK 24-22-33-000-001) and (Ref. AMM TASK 24-22-33-400-002).
(1) If the fault continues:
- do a check of the wiring between: .the pin A/2B of the GCU2 (1XU2) and the pin A/7D of the EGIU2 (22XU2) .the pin A/2C of the GCU2 (1XU2) and the pin A/7C of the EGIU2 (22XU2). Then make sure that the ground wire is correctly connected to the pin A/6C of the EGIU2 (22XU2) (Ref. ASM 24-22/02).
(2) If the fault continues:
- replace the GCU-2 (1XU2) (Ref. AMM TASK 24-22-34-000-001) and (Ref. AMM TASK 24-22-34-400-001)
D. If the test confirms the fault:
- do a check and repair the wiring (Ref. ASM 31-54/03) between: . the pin A/1A of the EGIU2 (22XU2) and the pin B/10G of the SDAC1 (1WV1) . the pin A/1B of the EGIU2 (22XU2) and the pin B/10H of the SDAC1 (1WV1) . the pin A/1C of the EGIU2 (22XU2) and the pin B/10G of the SDAC2 (1WV2) . the pin A/1D of the EGIU2 (22XU2) and the pin B/10H of the SDAC2 (1WV2)
R **ON A/C 401-499,
R C. If the test confirms the fault:
R - replace the GCU-2 (1XU2) (Ref. AMM TASK 24-22-34-000-001) and (Ref. AMM
R TASK 24-22-34-400-001).
R D. If the test confirms the fault:
R - do a check and repair the wiring (Ref. ASM 31-54/03) between:
R . the pin A/8F of the GCU 2 (1XU2) and the pin E/10C of the SDAC 1 R (1WV1)
R . the pin A/7F of the GCU 2 (1XU2) and the pin E/10D of the SDAC 1 R (1WV1)
R . the pin A/8J of the GCU 2 (1XU2) and the pin E/10C of the SDAC 2 R (1WV2)
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞24-22-00∞∞∞∞∞∞∞∞∞∞Page 219
Aug 01/05 CES
R R . the pin A/8H of the GCU 2 (1XU2) and the pin E/10D of the SDAC 2 (1WV2).
R **ON A/C ALL
E. Do this test to make sure that the system operates correctly:
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
On the ECAM control panel: - push the ELEC key to get the ELEC page. On the lower ECAM DU:- the ELEC page comes into view.In the GEN 2 box: - the normal electrical parameters come into view.
5. Close-up________
A. Put the aircraft back to its initial configuration.
(1) Do the EIS stop procedure (Ref. AMM TASK 31-60-00-860-002).
(2) De-energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-862-002).
TASK 24-22-00-810-808
APU GEN Voltage, Frequency and Load Indication Lost or Incorrect
1. Possible Causes
_______________
- EGIU-2 (22XU2)
- GEN-APU (8XS)
- GCU-APU (1XS) R - GAPCU (24XG)
- wiring
- C/B APU GEN/EGIU2/115VAC (23XS)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 24-22-33-000-001 Removal of the EGIU-1(2) (22XU1, 22XU2)
AMM 24-22-33-400-002 Installation of the EGIU-1(2) (22XU1, 22XU2)
AMM 24-23-34-000-001 Removal of the GCU-APU (1XS)
AMM 24-23-34-400-001 Installation of the GCU-APU (1XS)
AMM 24-23-51-000-001 Removal of the APU Generator 8XS
AMM 24-23-51-400-001 Installation of the APU Generator 8XS
AMM 24-41-00-861-002 Energize the Aircraft Electrical Circuits from the
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 電源 2(137)
