S 865-148

 (6)  
Push and hold the TEST switch on the left ATC transponder.

 (a)  Make sure the sequence that follows occurs:
 1) All the LEDs come on momentarily.
 2) All the red LEDs go off.
 3) The green LED stays on.

 S 865-010
 (7)  Release the TEST switch on the ATC transponder.
 NOTE: The green LED will come on if the ATC transponder is
____
 interrogated.

 S 865-011
 (8)  
Set the transponder select switch on the ATC control panel to the R or 2 position.

 (9)  
Do the self-test procedure again for the right ATC transponder.

 (10)
 Set the transponder select switch on the ATC control panel to STBY.

 S 745-118
 S 865-007
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITHOUT MODE S ú

 34-53-00

 ú ú 01 Page 502 ú Jul 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 865-008
 (11) Remove electrical power if it is not necessary (Ref-24-22-00/201).
 TASK 34-53-00-735-009
 3.  ATC System Test - Using Collins 476X-3 Test Set_______________________________________________
 A. General
 (1)  This system test is a more complete check of the ATC system. The system test first does the ATC Operational Test. Then uses a ramp test to examine the left and the right ATC system.
 B. Standard Tools and Equipment
 (1)  
ATC Transponder Ramp Test Set - Collins 476X-3

 (2)  
Air Data Test Set, Castleberry AT700-2, Castleberry Instr & Avionics, Austin, TX; or equipment.

 C. References
 (1)  
AIRPLANES WITH EFIS;
 AMM 34-11-01/501, Pitot Static System

 (2)  
AIRPLANES WITHOUT EFIS;
 AMM 34-11-00/501, Pitot Static System

 (3)  
AIRPLANES WITHOUT EFIS;
 AMM 34-12-00/501, Air Data Computer System

 (4)  
AIRPLANES WITH EFIS;
 AMM 34-12-01/501, Air Data Computer System

 (5)  
24-22-00/201, Manual Control

 D. Access
 (1)  
Location Zones
 101/102 Flight Compartment
 205 Electronic Compartment

 (2)  
Access Panels
 1201 Electronics Equipment Access Door

 E. Prepare for the System Test
 S 865-012
 (1)  Calibrate the Collins 476X-3 test set as follows:
 (a)  
Set the 476X-3 MODE selector switch to A-B-C. 1) Make sure the mode flags show A to B and to C in sequence

 (b)  
Set the MODE selector switch to the SELF-TEST position.

 (c)  
Set the T/R ATTEN to 25 db. 1) Make sure the battery is fully charged.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITHOUT MODE S ú

 34-53-00
 ú ú 02 Page 503 ú Mar 15/96

BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (d) (e) (f)  To calibrate R-F OUTPUT, set the MODE SELECTOR to SELF-TEST.Set the CALIBRATE OUTPUT/BATTERY VOLTAGE switch to the calibrate output position.Adjust OUTPUT to get a red line indication on the meter.
 (2)  S 715-013Do a self test of the Collins 476X-3 as follows: (a) Set the MODE SELECTOR switch to SLEF-TEST. (b) Set the T-R ATTEN switch to 25 db. 1) Make sure the test set shows the IDENT flag. (c) Set the code selector to code, 0000 1) Make sure the test set show the CODE and IDENT flags. (d) Set the code selector to code 7777. 1) Make sure the test set show the CODE and IDENT flags. (e) Set the code selector to code 7773. 1) Make sure the test set show the CODE (blinking) and IDENT flags. (f) Set the code selector to code 0004. 1) Make sure the test set show the CODE (blinking) and IDENT flags.
 (3)  S 865-014Put the 476X-3 test set about 40 to 50 feet away from the ATC antenna.
 NOTE:____ To get accurate results, the test set must be visible from the cockpit, and there should be a line of sight between the test set and the ATC antenna.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 導航 NAVIGATION 3(157)