34-35-11

 ALL  ú ú 01 Page 401 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (2)  
AMM 51-21-31/701, Corrosion Removal and Control

 (3)  
SRM 51-20-01

 (4)  
AMM 51-31-00/201, Seals and Sealing

 D. Access
 (1)  Location Zone
 215 Keel Beam

 E. Procedure
 S 864-006
 (1)  Make sure this circuit breaker is open:
 (a)  P18 Load Control Center - Left
 1) MARKER BEACON

 S 144-007
 (2)  
Do this task to remove the old sealant from the airplane skin: "Faying Surface Seal Application" (AMM 51-31-00/201).

 S 114-008

 (3)  
Do this task to clean the airplane surface with the solvent and rag: "Aluminum Corrosion Removal" (AMM 51-21-31/701).

(6 LOCATIONS)
Marker Beacon Antenna Installation (Example) Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-35-11

 ALL  ú ú 01 Page 402 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 S 394-011
 (4)  
Do this task to prevent corrsion to the airplane surface: Apply the Corrsion Inhibiting Compound (SRM 51-20-01).

 S 424-009

 (5)  
Install the marker beacon antenna:

 (a)  
Connect the electrical connector to the antenna.

 (b)  
Align the antenna with the holes in the fuselage.

 (c)  
Install the screws in the antenna base.

 (d)  
Tighten the screws.

 F. Resistance Measurement
 S 034-009
 (1)  
Remove one of the screws from the antenna base.

 S 484-010

 (2)  
Connect the bonding meter between the mounting screw hole and the airplane skin.

 S 224-010

 (3)  
Do this task to do a check of the resistance between the antenna base and the airplane skin: "Electrical Bonding Check" (SWPM 20-20-00).

 (a)  Make sure the resistance is not more than 0.001 ohm.
 S 394-005
 (4)  Do this task to apply weather/aerodynamic fillet to the antenna: "Aerodynamic Smoother Application" (AMM 51-31-00/201).
 NOTE: Apply the aerodynamic smoother to the leading edge of the
____
 antenna only.

 S 864-003
 (5) Remove the DO-NOT-CLOSE tag and close this circuit breaker:
 (a)  P18 Load Control Center - Left
 1) MARKER BEACON

 S 864-004
 (6)  Do this task to supply electrical power: "Manual Control" (AMM 24-22-00/201).
 TASK 34-35-11-704-006
 4. Marker Beacon Antenna Test
__________________________
 A. Standard Tools and Equipment
 (1)  Ramp Test Set Instrument Flight Research - NAV-401L
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-35-11

 ALL  ú ú 01 Page 403 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 B. References
 (1)  AMM 24-22-00/201, Manual Control
 C. Access
 (1)  Location Zone
 215 Keel Beam

 D. Procedure
 S 714-008
 (1)  Do the marker beacon antenna test:
 (a)  
Put the ramp test set approximately 15 feet away from the marker beacon antenna.

 (b)  
Turn on the ramp test set.

 (c)  
Set the ramp test set to supply a 75 MHz signal with 400 Hz modulation. 1) Make sure light for the OUTER marker beacon on the

 captains' instrument panel comes on.

 (d)  
Turn off the ramp test set.

 S 864-015
 (2)  Do this task to remove electrical power if it is not necessary: "Manual Control" (AMM 24-22-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 導航 NAVIGATION 3(42)