(c)
Remove the dust caps from the electrical connectors.
(d)
Connect the coaxial cables to the antenna.
(e)
Align the leading edge with the screw holes on the top of the vertical fin.
(f)
Install the screws.
S 224-019
(4) Do this task to do a check of the resistance between the antenna base and airplane skin: Electrical Bonding Check (SWPM 20-20-00).
(a) Make sure the resistance is not more than 0.001 ohm.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-31-11
ALL ú ú 04 Page 402 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(5) S 714-027Do the VOR test in the VOR/ILS System Test to make sure the antenna operates satisfactorily (AMM 34-31-00/501, 34-31-02/501).
(6) S 864-031If electrical power is not necessary: Do this task to remove electrical power: (AMM 24-22-00/201) Manual Control
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-31-11
ALL ú ú 05 Page 403 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
VOR/LOC ANTENNA
RF CONNECTORS
VOR/LOC ANTENNA ASSEMBLY
VOR/LOC Antenna Installation
Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-31-11
ALL ú ú 01 Page 404 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
GLIDE SLOPE ANTENNA - REMOVAL/INSTALLATION
__________________________________________
1. General_______
A. This subject has two tasks. The first task is the removal of the glide slope antenna. The second task is the installation of the glide slope antenna and a test of the glide slope antenna.
TASK 34-31-21-004-001
2. Glide Slope Antenna Removal (Fig. 401)___________________________
A. General
(1) The glide slope antenna (M40) is installed in the nose radome (Fig. 401).
B. References
(1)
AMM 53-52-00/401, Nose Radome
(2)
AMM 53-52-31/401, Glide Slope Antenna Director Bar
C. Access
(1) Location Zone
201 Nose Radome
D. Procedure
S 024-015
WARNING: MAKE SURE THE WEATHER RADAR POWER IS OFF AND THE ANTENNA CANNOT
_______ MAKE A SCAN. IF THE WEATHER RADAR TRANSMITS OR MAKES A SCAN, INJURY TO PERSONS CAN OCCUR.
(1)
Open the nose radome (AMM 53-52-00/401).
S 754-016
(2)
Make sure the antenna director bar is not damaged.
NOTE: The antenna director bar is a 13-inch continuous strip of aluminum foil tape. The strip is installed horizontally across the centerline on the inner surface of the nose radome. It is approximately 22 inches from the lower edge of the nose radome.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-31-21
ALL ú ú 02 Page 401 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(a) If the director bar is damaged, replace the antenna director bar (AMM 53-52-31/401).
S 024-017
(3) Remove the glide slope antenna:
(a)
Remove the screws that attach the glide slope antenna to the airplane structure (Fig. 401).
(b)
Pull the antenna assembly away from the airplane structure to get access to the coaxial cables.
(c) 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 導航 NAVIGATION 3(17)
