曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

2) 3) 4)  AUTO FLT CONT SYS A MACH TRIM DCAFDS MCP DCAIRPLANES WITH MECHANICAL AILERON FORCE LIMITER; AFDS AIL FORCE LIM
 5) 6) 7) 8) 9)  AUTO FLT CONT SYS A SNSR EXC ACAUTO FLT CONT SYS A FCC DCAUTO FLT CONT SYS A ENGAGE INTLK AAUTO FLT CONT SYS A WARN LIGHT BATAUTOPILOT STABILIZER TRIM SERVO
 S 864-021
 (3)  Install the stabilizer trim lock assembly on the stabilizer trim wheel.
 (a) (b) (c)  Turn the trim wheel to put the handle at the top of the wheel.Adjust the height of the trim lock to set the trim wheel handle tightly in the bottom of the yoke.Install the pin through the yoke and install the safety pin.
 S 864-022
 (4)  Open this circuit breaker and attach a DO-NOT-CLOSE tag. (a) E3-3 Electrical Shelf, APU Control Unit
 S 014-004
 (5)  Open the access door for the horizontal stabilizer compartment.
 S 024-013
 (6)  Disconnect the electrical connector from the stabilizer trim electric actuator.
 S 024-014
 (7)  Disconnect the electrical connector from the autopilot stabilizer trim servo.
 S 424-015
 (8)  Install caps on the electrical connectors and receptacles for protection.
 S 024-005
 (9)  Remove the shutoff valve: (a) Disconnect the pressure line from the pneumatic actuator. 1) Install caps on the pressure line and the pneumatic actuator for protection.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 49-51-21
 ALL  ú ú 01 Page 405 ú Nov 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / GTCP85-129 SERIES /737-300/400/500/ ENGINES/MAINTENANCE MANUAL ////////////////////////
(b)  Remove the nuts and the washers that attach the shutoff valve to the upper shroud.
 NOTE: The bolts are attached to the upper shroud.
____
 (c)  Remove the shutoff valve from the upper shroud through the horizontal web opening.
 TASK 49-51-21-404-006
 3. Cooling Air Shutoff Valve Installation (Fig. 401)
______________________________________
 A. Consumable Materials
 (1)  
A00027 Sealant - BAC5010, Type 60

 (2)  
D00013 Grease - MIL-G-23827

 (3)  
G00001 Agent - Parting

 B. References
 (1)  AMM 49-51-21/501, Cooling Air Shutoff Valve
 C. Access
 (1)  
Location Zones
 101 Control Cabin, LH
 205 Electronic Compartment
 701 Tail Compartment
 703 APU Compartment

 (2)  
Access Panels
 1201 Electronic Equipment Access Door
 3701 Stabilizer Compartment Access Door

 

 D. Procedure
 S 864-016
 (1)  Make sure the switch and the circuit breaker are set correctly:
 (a)  
Make sure the APU master switch, on the P5 forward overhead panel, is in the OFF position with a DO-NOT-OPERATE tag attached.

 (b)  
Make sure this circuit breaker is open with a DO-NOT-CLOSE tag attached: 1) E3-3 Electrical Shelf, APU Control Unit

 S 864-017
 (2)  Make sure the electrical connectors are disconnected:
 (a)  
Make sure the electrical connector is disconnected from the stabilizer trim electric actuator.

 (b)  
Make sure the electrical connector is disconnected from the autopilot stabilizer trim servo.

 S 424-007
 (3)  Install the shutoff valve:
 (a)  Apply a thin layer of the grease to the shaft on the shutoff valve.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 49-51-21
 ALL  ú ú 01 Page 406 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(b)  Apply the parting agent to the mating surface of the shutoff valve.
 (c) (d)  Apply the sealant to the mating surface between the shutoff valve and the cutout of the duct assembly.Install the valve through the horizontal web opening and align the bracket holes with the bolts in the upper shroud. 1) Make sure the shutoff valve tightly fits over the air inlet duct.
 (e)  Install the nuts and the washers that attach the shutoff valve to the bracket.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 AIRBORNE AUXILIARY POWER 2(65)