(2)
G00287 Parting Agent - Delchem X-769
C. Access
(1) Location Zones
200 Lower Half of Fuselage
D. Procedure
S 014-002-B00
(1)
If the panel blows out, open the underwing fairing and remove the rivets.
S 144-003-B00
(2)
Use a wooden or plastic spatula to clean the sealant from the mating surfaces.
S 124-004-B00
(3)
Apply an abrasion resistant finish and parting agent to the outer face of the fairing lip (Ref 51-21-81/701).
S 144-005-B00
(4)
Remove the sealant from the clearance between the blowout panel and panel cutout.
S 394-006-B00
CAUTION: BE CAREFUL WHEN YOU APPLY HAND PRESSURE TO PUT THE BLOWOUT
_______ PANEL IN THE CORRECT POSITION. TOO MUCH PRESSURE CAN CAUSE DISTORTION OF THE BLOWOUT PANEL.
(5)
Before you install the blowout panel, apply a bead of sealant to the inner face of the panel lip (Ref 51-31-00/201).
S 864-007-B00
(6)
After the sealant dries, open and close the blowout panel to make sure it does not bond.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
53-51-11
ALL ú ú B02 Page 401 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
TASK 53-51-11-404-008-B00
3. Install the Blowout Panel for the Wing-to-Body Fairing______________________________________________________
A. Consumable Materials
(1) Rivets - MS20470A, 3/32-inch diameter and 1/8-inch diameter
B. Access
(1) Location Zones
200 Lower Half of Fuselage
C. Procedure
S 214-009-B00
(1)
Examine the attach clips for damage.
S 434-010-B00
(2)
Install the blowout panels with one rivet, 3/32-inch diameter, in the aft outboard location and one rivet, 1/8-inch diameter, in the forward outboard location.
(3)
Close and latch the blowout panel.
S 864-011-B00
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
53-51-11
ALL ú ú B01 Page 402 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
FORWARD WING-TO-BODY FAIRING - REMOVAL/INSTALLATION
___________________________________________________
1. General_______
A. This procedure has these tasks:
(1)
Forward Wing-to-Body Fairing Removal.
(2)
Forward Wing-to-Body Fairing Installation.
TASK 53-51-19-004-001-B00
2. Forward Wing-to-Body Fairing Removal____________________________________
A. General
(1) The wing-to-body fairing will be referred to as the fairing in this task.
B. References
(1)
AMM 12-31-21/201, Body Section 43 Access Doors and Panels
(2)
AMM 12-31-31/201, Body Section 46 Access Doors and Panels
C. Access
(1) Location Zone
300/400 Left Wing/Right Wing
D. Procedure
S 034-002-B00
(1) If it is necessary, remove or disconnect the equipment that is attached to the fairing.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 機身 FUSELAGE(18)
