(2)
Apply BMS10-21 Type II anti-static paint to the entire outer radome surface.
(3)
Apply masking tape to a 5-inch vertical band area all around the radome from STA 138.6 to STA 143.6 and apply BMS10-79 Type II primer on the radome except for the band area.
(4)
Apply BMS10-60 Type II enamel to the radome except for the band area.
(5)
Remove the masking tape from the 5-inch vertical band area and apply a second coat of BMS10-21 Type II anti-static coating to the band area only.
(6)
Apply masking tape and masking materials aft of STA 138.6 and apply BMS10-60 Type II enamel for the erosion coating from the radome nose tip to STA 138.6.
TASK 53-52-00-307-001-B00
2. Nose Radome - Cleaning and Painting___________________________________
A. Consumable Materials
(1)
B00083 Solvent, Aliphatic Naphtha - TT-N-95
(2)
C00033 Coating - BMS 10-60 Type II, Exterior Protective Enamel
(3)
C00319 Coating - BMS10-79 Type II, Urethane Compatible Primer, Corrosion Resistant
(4)
C00841 Coating, BMS10-21 Type II, Antistatic Coating
(5)
G00034 Cloth, BMS5-15 Process Cleaning Absorbant Wiper (cheesecloth, gauze)
(6)
G00270 Tape, 3M #250 (A-A-883), Masking, General Purpose
B. References
(1)
AMM 51-21-21/701, Cleaning and Preparation of Internal and External Plastic Surfaces
(2)
AMM 51-21-99/701, Decorative Exterior Paint System Application
(3)
AMM 53-52-00/401, Nose Radome - Removal and Installation
(4)
AMM 53-52-03/201, Lightning Diverter Strips - Removal and Installation
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
53-52-00
ALL ú ú B02 Page 701 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
C. Access
(1) Location Zone
111 Radome
D. Prepare the Nose Radome Surface for Paint
S 027-063-B00
(1)
Remove the nose radome from the airplane (AMM 53-52-00/401).
S 027-064-B00
(2)
Remove all lightning diverter strips from the nose radome
(53-52-03/201).
S 937-065-B00
(3)
Identify the lightning diverter strips for subsequent installation.
S 107-066-B00
(4)
Clean and prepare the surface of the nose radome (AMM 51-21-21/701).
(a)
Solvent clean the surface of the radome with naphtha.
(b)
Abrade the surface of the nose radome.
S 307-067-B00
(5) If there are surface defects, do these steps:
CAUTION: ONLY USE THE STATIC CONDITIONER FILLER TO FILL SMALL
_______ SURFACE DEFECTS SUCH AS PINHOLES. DO NOT USE THE FILLER TO MAKE LARGE AREAS SMOOTH. A CONTINUOUS LAYER OF FILLER WILL CAUSE A BAD PAINT BOND.
(a)
Apply the static conditioner filler 28-C-1 to small surface defects.
(b)
Let the filler dry.
(c)
Remove unwanted filler with a clean dry cloth, BMS15-5.
NOTE: Do not use solvents to remove the remaining filler.
____ Solvents will remove the static conditioner on touch.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
53-52-00
ALL ú ú B02 Page 702 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
CAUTION:_______DO NOT APPLY THE SURFACER MORE THAN 0.002 INCH THICK. IF YOU NEED MORE THAN 0.002 INCH YOU MUST USE PUTTY.
(d)
If there are surface defects that you cannot fill with the filler, use the Laminar X-500 Off-White Surfacer, 8-W-5.
(e)
Let the surfacer dry.
E. Procedure
S 377-068-B00
(1) Mix the anti-static coating, BMS10-21, Type II as follows:
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機(jī)維護(hù)手冊 機(jī)身 FUSELAGE(29)
