DIVERTER STRIP
SURFACE  PERIPHERY OF MOLDED FASTENER. OF BMS 5-95 IS ACCEPTABLE AROUND 
SEALANT FILLET  NYLON 

RADOME SHELL INTERIOR SURFACE INSERT

Insert/Sealant Installation
Figure 202

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 53-52-03
 ALL  ú ú B01 Page 205 ú Nov 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
K80013
A 737-300/400/500MAINTENANCE MANUAL
 (2)  S 212-017-B00Make sure the electrical resistance between the points shown in Fig. 201 is less than 10 milliohms.
 (3)  S 412-018-B00Close the nose radome (AMM 53-52-00/401).
 (4)  S 212-019-B00Make sure the electrical resistance between the diverter strip and the forward bulkhead is less than 30 milliohms.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 53-52-03
 ALL  ú ú B01 Page 206 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 GLIDE SLOPE ANTENNA DIRECTOR BAR - REMOVAL/INSTALLATION
_______________________________________________________
 1.  General
_______
 A.  There are two tasks in this procedure. There is one task for the removal and one task for the installation of the director bar for the glide slope antenna.
 B.  The director bar for the glide slope antenna is an aluminum foil pressure-sensitive strip of tape. The director bar is attached to the inner surface of the nose radome. It changes the radiation signals for the glide slope antenna.
 TASK 53-52-31-004-001-B00
 2.  Glide Slope Director Bar Removal
________________________________
 A.  Access
 (1)  Location Zone
 201 Radome

 B.  Procedure (Fig. 401)
 S 864-012-B00
 (1)  Open these circuit breakers and attach DO-NOT-CLOSE tags:
 (a)  P18 Load Control Center - Left
 1) WEATHER RADAR AC
 2) WEATHER RADAR DC

 S 014-002-B00
 (2)  Open the nose radome.
 (a)  Remove the screws which attach the radome to the clips on the fuselage.
 CAUTION: DO NOT OPEN THE RADOME IF THE WIND SPEED IS MORE THAN
_______ 15 KNOTS. THIS CAN CAUSE DAMAGE TO THE RADOME.
 (b)  
Open the radome.

 (c)  
Install the support rod to hold the radome open.

 S 024-003-B00
 (3)  Remove the director bar.
 TASK 53-52-31-404-004-B00
 3.  Glide Slope Director Bar Installation
_____________________________________
 A.  Consumable Materials
 (1)  
B00316 Solvent - Aliphatic Naphtha

 (2)  
B00192 Solvent - BMS 3-2, Type I

 (3)  
C00259 Enamel - Primer

 (4)  
G02095 Tape - Aluminum Foil Pressure Sensitive

 -No. 425, 1/2-inch wide, BAC5801
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 53-52-31
 ALL  ú ú B01 Page 401 ú Nov 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL

Director Bar - Glide Slope Antenna Installation
Figure 401

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 53-52-31
 ALL  ú ú B01 Page 402 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 B. References
 (1)  53-52-00/401, Nose Radome
 C. Access
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 機身 FUSELAGE(33)