S 094-065-C00

 (10)
 Remove the inlet cowl from the work area.

 TASK 71-11-01-404-067-C00
 5. Install the Inlet Cowl (Nose Cowl Dolly - Optional Method)
__________________________________________________________
 A. Equipment
 (1)  
Nose Cowl Dolly-AM-1940
 Advanced Ground Systems
 1265 N. Kraemer Blvd.
 Anaheim, Ca. 92806

 B.
Consumable Materials

 (1)  
Adhesive - Rubstrip - BMS 5-109, Type II, Class 2, Grade A

 (2)  
Rubstrip - KWS100011

 (3)  
Sealant - Pro Seal 860, Class B

 C.
References

 (1)  
AMM 71-11-01/601, Inlet Cowl - Inspection/Check

 (2)  
AMM 71-11-02/201, Fan Cowl Panels

 D.
Access

 (1)  
Location Zone
 506 Engine No. 1 - Fan Frame
 606 Engine No. 2 - Fan Frame

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-11-01
 ALL  ú ú C01 Page 423 ú Mar 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(2)  
Access Panel
 5746 Fan Cowl Panel (LH) - Engine No. 1
 5846 Fan Cowl Panel (LH) - Engine No. 2

 E.
Procedure

 S 964-091-C00
 (1)  Replace the rubstrip by removing the peel ply and using adhesive BMS 5-109 while equally installing the rubstrips on the inlet chord extrusion. (Fig. 405A)
 NOTE: If rubstrips are located between the inlet aft chord and the
____ strut fairing, they need to be inspected before the inlet cowl is installed. (AMM 71-11-01/601)
 S 014-066-C00
 (2)  
If not already open, open fan cowl panels (AMM 71-11-02/201).

 S 494-067-C00

 (3)  
Do these steps to prepare the dolly for the installation (Fig. 406):

 (a)  
Make sure the engine cowling strap is tightened around the inlet cowl to hold the cowl to the dolly.

 WARNING:_______BE CAREFUL WHEN YOU MOVE THE INLET COWL. BECAUSE THE INLET COWL WEIGHS 255 POUNDS (116 KG), INJURIES TO PERSONS CAN OCCUR.

 (b)  
Move the dolly with the inlet cowl below the engine inlet attachment flange.

 (c)  
Use the hand jacks to lift the dolly and inlet cowl to the height of the engine inlet attachment flange.

 (d)  
Make sure the shear pins at the 3:10 and 8:50 o'clock positions on the engine inlet attachment flange are correctly installed.

 (e)  
Position the inlet cowl with the holes in the attachment flange aligned with the shear pins in the engine inlet attachment flange.

 (f)  
Level and align the inlet cowl with the hand jacks on the dolly and install the inlet cowl.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-11-01
 ALL  ú ú C01 Page 424 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 424-088-C00
 CAUTION: USE PRECAUTION TO PREVENT DAMAGE TO THE STRUT FIRE/OVERHEAT
_______ DETECTOR ELEMENTS, GENERATOR, GENERATOR COOLING DUCT, AND HYDRAULIC HOSES. RESTRICTIONS TO MOVEMENT ARE AS FOLLOWS:
 1.  
ONE-HALF INCH (12.7 MM) CLEARANCE BETWEEN INLET COWL ATTACHMENT FLANGE AND UNDER SURFACE OF STRUT. LIMITS APPLY TO ALL VERTICAL MOVEMENT.

 2.  
ONE-TENTH INCH (2.54 MM) CLEARANCE BETWEEN AERODYNAMIC SEAL AND INLET COWL STEP APPROXIMATELY 24 INCHES (610 MM) IN LENGTH EXTENDING FROM 11:30 THROUGH 12:30 O'CLOCK POSITION. LIMITS APPLY TO VERTICAL MOVEMENT FOR FIRST INCH (25.4 MM) OF FORWARD TRAVEL FROM THE ENGINE INLET ATTACHMENT FLANGE.

 3.  
ONE-HALF INCH (12.7 MM) CLEARANCE BETWEEN INLET COWL ATTACHMENT FLANGE AND GENERATOR AT THE 8 O'CLOCK POSITION. LIMITS APPLY TO FORWARD MOVEMENT TO 0.75 INCH (19.05 MM) AND ALL SIDE MOVEMENT TO THE LEFT.

 4.  
ONE-HALF INCH (12.7 MM) CLEARANCE BETWEEN FEEDER CABLE BRACKET AND INLET COWL ATTACHMENT FLANGE. LIMITS APPLY TO ALL UPWARD AND LEFT SIDEWAYS MOVEMENT FOR FIRST 5 INCHES (127 MM) OF FORWARD TRAVEL FROM THE ENGINE INLET ATTACHMENT FLANGE.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 動力裝置 POWER PLANT 2(119)