(2)
Access Panels
5746/5846 Fan Cowl Panel (LH)
5737/5837 Fan Cowl Panel (RH)
D.
Adjust the Latch Bolt
NOTE: The fan cowl panel lower latches must be correctly adjusted
____
before the forward latch adjustment.
S 015-015-C00
(1)
Open the applicable fan cowl panel (Ref 71-11-02/201).
S 415-016-C00
(2)
Put the modeling clay on the striker and close the fan cowl panel (Ref 71-11-02/201).
S 015-017-C00
(3)
Open the applicable fan cowl panel (Ref 71-11-02/201).
S 225-018-C00
(4)
Make sure the clearance between the latch bolt and striker is
0.00 - 0.01 inches (0.00 - 0.25 mm) maximum.
S 825-019-C00
(5)
If the latch bolt clearance is more than the limits, loosen the locknuts and turn the latch bolt to decrease the clearance.
(a)
When you have the correct clearance, tighten the locknuts.
(b)
Safety the locknuts with a lockwire.
(6)
Close the fan cowl panel (Ref 71-11-02/201).
S 415-020-C00
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-11-03
ALL ú ú C01 Page 508 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 225-021-C00
(7) Make sure the free play at the aft end of the latch handle is 0.00 - 0.02 inches (0.00 - 0.51 mm) maximum.
S 225-022-C00
(8) With the latch trigger in the fully locked position, make sure the trigger is aligned, |0.02 inch (|0.51 mm), with the forward and aft parts of the latch.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-11-03
ALL ú ú C01 Page 509 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
CSD ACCESS DOOR - MAINTENANCE PRACTICES
_______________________________________
1. General_______
A. This procedure contains three tasks. The first task is to remove and
install the CSD door latches. The second task is to remove and install
the CSD door. The third task is to adjust the CSD door.
TASK 71-11-04-902-001-C00
2. Latch Removal/Installation (Fig. 201)__________________________
A. Consumable Materials
(1)
Primer - BMS 10-11 (Type I) (Ref 70-10-01)
(2)
Sealant - BMS 5-95 (Ref 70-10-01)
(3)
Sealant - DC 93-006-1 (Ref 70-10-01)
B.
Equipment
(1)
Heat gun - local purchase
C.
Access
(1)
Location Zones
506 Engine No. 1 - Fan Frame
606 Engine No. 2 - Fan Frame
(2)
Access Panels
5740/5840 Access Door CSD
D.
Remove the Latch.
S 012-002-C00
(1) Open the CSD access door.
(a)
Push the large end of each latch into the door.
(b)
Help the door correctly open down to the fully open position.
S 032-003-C00
(2)
Remove the screws, nuts, and washers (4 locations each) that attach the latch to the door.
S 032-004-C00
(3)
Remove the latch from the CSD access door.
E.
Install the CSD door latch.
S 372-005-C00
(1) Apply two layers of primer to the faying surfaces of the latch.
(a) Dry the primer for 5 minutes with a heat gun.
S 432-006-C00
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 動力裝置 POWER PLANT 2(138)
