曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 S 864-019
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LE FLAPS
_______ BEFORE YOU MOVE THE REVERSE THRUST LEVERS. THE ENGINE THRUST REVERSER SLEEVES WILL OPEN IN 1 1/2 SECONDS AND CLOSE IN 4 1/2 SECONDS WHEN YOU OPERATE THE LEVERS. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (6)  Do this task to pressurize hydraulic systems No. 1 and No. 4: "Hydraulic System Pressurization" (AMM 29-11-00/201).
 NOTE: Hydraulic power is not necessary if you use the reverse
____
 thrust levers to retract and extend the LE flaps.

 S 864-031
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LE AND TE
_______ FLAPS AND FLAP DRIVE MECHANISMS BEFORE YOU MOVE THE FLAP CONTROL LEVER. WITH HYDRAULIC POWER REMOVED, THE FLAPS WILL MOVE AUTOMATICALLY BY ELECTRICAL POWER WHEN YOU MOVE THE FLAP CONTROL LEVER. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (7) Extend the trailing edge flaps to a minimum of 5 unit detent.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-81-06
 ALL  ú ú 01 Page 409 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (8)  S 864-021Do this task:  "Supply Pneumatic Power" (AMM 36-00-00/201).
 (9)  S 864-022Move the flap LE flaps. control lever to the full UP position to retract the
 S 224-023

 (10)
 Examine if the flap contour at the aft edge of the flaps is in the specified limits (Detail A, Fig. 401).

 (a)  
Adjust the contour if it is out of tolerance: 1) Move the flap control lever to the 5 unit position to extend the LE flaps. 2) Disconnect the drive shafts adjacent to the rotary

 actuator. 3) Turn the actuator spline in the applicable direction.
 NOTE: The flap trailing edge will move 0.054 inch with one
____ spline tooth turn.
 a)  Hold the other drive shaft linkages to prevent adjustment changes to these linkages.
 4)  Connect the drive shaft to the actuator.
 5)  Install the coupling with screws.
 6)  Install the lockwire.
 7) Move the flap control lever to the full UP detent to retract the LE flaps. 8) Examine the flap contour again.
 S 864-024
 (11)
 Move the flap control lever to the 5 unit detent to extend the LE flaps.

 S 224-025

 (12)
 Do a check on the retract stop clearance:

 NOTE: If it is necessary, do this check again until you get the
____ correct clearance.
 (a)  Push a small rod through the hole of the retract stop bolt to extend the clearance indicator pin 0.15 to 0.20 inch (Section C-C, Fig. 401).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-81-06
 ALL  ú ú 01 Page 410 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (b)  
Operate the flaps pneumatically. 1) Move the flap control lever to the full UP position. 2) Move the flap control lever to the 5-unit detent.

 (c)  
Measure the height of the clearance indicator pin (Section B-B, Fig. 401).

 (d)  
Move the washers to adjust the retract stop until you get the correct clearance.

 (e)  
Push the indicator pin to the stop bolt head.

 (f)  
Install the lockwire on the coupling bolts.

 (g)  
Move the flap control lever to full UP detent to retract the LE flaps.

 S 824-026
 (13)
 Adjust the seals, if it is necessary.

 (a)  
Make sure all the seals touch.

 (b)  
Adjust the seals if they do not touch.

 G.
Put the Airplane Back to Its Usual Condition

 S 864-027
 (1)  
Do this task:: "Hydraulic System Depressurization"
 (AMM 29-11-00/201).

 S 864-028

 (2)  
Do this task if pneumatic power is not necessary: "Pneumatic Power Removal" (AMM 36-00-00/201).

 S 864-029

 (3)  
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護(hù)手冊 飛行操縱 FLIGHT CONTROLS 7(134)