NOTE: The installation bolt goes the through the lower mounting
____ bracket, the shaft and the support block assembly on the upper mounting bracket.
 S 434-017
 (3)  
Tighten the bolt and safety it with a bolt retainer.

 S 434-018

 (4)  
Install the steering system cables (NWS1A, NWS1B) to the steering quadrant.

 (a)  
Safety the cables to the quadrant with the cotter pins.

 S 494-019
 (5)  
Make sure that you install the rigging pins that follow
 (AMM 32-51-00/501):

 (a)  
Rigging pin No. 1 in the steering tiller of the captain

 (b)  
Rigging pin No. 2 in the steering tiller of the first officer

 (c)  
Rigging pin No. 4 in the cable compensator.

 S 834-020
 (6)
Adjust the steering (NWS1A, NWS1B) cables (AMM 32-51-00/501).

 S 434-021

 (7)  
Connect the steering rod to the steering crank.

 S 434-022

 (8)  
Install the rudder pedal interconnect actuator No. 1
 (AMM 32-51-07/401).

 S 094-023

 (9)  
Remove all the rigging pins.

 F.
Rudder Pedal Steering Mechanism Test

 S 014-024
 (1)  Disconnect the torsion links of the nose gear at the top
 (AMM 32-21-03/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-02
 ALL  ú ú 01 Page 405 ú Oct 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 724-025
 (2)  
Do a test on the turn of the nose gear.

 (a)  
Use the upper torsion link to turn the steering collar to the left (CCW) until the steering actuators are at their limits. 1) Make sure that the angular movement of the nose gear is

 70 (+2/-3) degrees.
 2)  Make sure that these items are free to move and have no worn areas: a) the cables b) the pulleys c) the quadrants d) the tillers e) the rudder pedal steering system f) the summing mechanism g) the steering actuators.
 (b)  Do the above turn test but manually turn the steering collar of the nose gear clockwise.
 S 864-026
 (3)  
Supply electrical power (AMM 24-22-00/201)

 S 734-027

 (4)  
Do a check on the steering system of the rudder pedal.

 (a)  
Set the rudder system to OFF.

 1)  On the P461 Pilot's Overhead Maintenance Panel, put the FLT CONTROL HYD POWER - TAIL VALVE switches No. 1, 2, 3, and 4 in the SHUTOFF position.
 CAUTION: OPEN THE SPECIFIED CIRCUIT BREAKERS BEFORE YOU DO THE
_______ PROCEDURES THAT FOLLOW. FAILURE TO OPEN THE CIRCUIT BREAKERS CAN CAUSE DAMAGE TO THE EQUIPMENT OR UNWANTED EQUIPMENT OPERATION TIME.
 2)  Open these circuit breakers and attach DO-NOT-CLOSE tags on the P180 DC Power Distribution Panel: a) 180H8 ELEV/RUD VLV SYS 1 b) 180E7 ELEV/RUD VLV SYS 2 c) 180H23 ELEV/RUD VLV SYS 3 d) 180E22 ELEV/RUD VLV SYS 4
 3) Close the 7G25 NOSE GR STRG PRI circuit breaker on the P7 Overhead Circuit Breaker Panel. 4) Close the 7G26 NOSE GR STRG ALTN circuit breaker on the P7 Overhead Circuit Breaker Panel.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-02
 ALL  ú ú 01 Page 406 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (b)  
Pressurize hydraulic system No. 1 (AMM 29-11-00/201).

 (c)  
Push the left rudder pedal of the captain fully forward.

 (d)  
Make sure that the steering collar of the nose gear has turned 7 (|1) degrees from the straight-forward position.

 (e)  
Release the rudder pedal of the captain and permit it to go back to the neutral position.

 (f)  
Make sure that the rudder pedal of the captain goes back to the adjusted neutral position (AMM 27-21-00/501).

 (g)  
Make sure that the steering collar of the nose gear goes to neutral (| 2.0 degrees).

 (h)  
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 8(12)