(t)  
Lubricate the O-ring (6) with grease and place the O-ring in position.

 (u)  
Assemble a new lubricated O-ring (7) on the retainer bolt (8).

 (v)  
Install the retainer bolt in the right pin (5) and tighten the retainer nut (4) to 10-15 pound-feet.

 (w)  
Fill the area around the retainer nut (4) with grease.

 (x)  
Install the lube insert (3) with O-rings (2) in the collar pin

 (5)
 and secure it with the retainer ring (1).

 (y)  
Tighten the clamps and the couplings on the electrical conduit and do a check of the security of the electrical boxes on the nose gear (Fig. 402).

 (13)
 Check the collar for free turning in both directions.

 S 434-022

 (14)
 Do this task:  "Torsion Links Installation (Fig./401)" (AMM 32-21-03/401).

 S 714-021
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-06
 ALL  ú ú 01 Page 411 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 644-023
 (15)
 Thoroughly lubricate the unit thru the collar fittings until grease extends from the ends of the collar halves.

 S 834-024

 (16)
 Install and rig the steering cables (NWS2A, NWS2B) (AMM 32-51-00/501).

 S 094-025
 WARNING:_______REFER TO AMM 32-00-30/201 FOR LOCK REMOVAL PROCEDURE. RAPID ACTION OF DOORS MAY INJURE PERSONNEL OR DAMAGE EQUIPMENT.
 (17) Remove the nose gear door lock (AMM 32-00-30/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-06
 ALL  ú ú 01 Page 412 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 NOSE GEAR STEERING COLLAR - INSPECTION/CHECK
____________________________________________
 1.  General_______
 A.  This subject has one task, determining the wear of the nose gear steering collar.
 (1)  
It measures the fit of the steering collar, the shock strut outer cylinder and the collar bushing.

 (2)  
It measures the fit of the steering cylinder rod end, the collar pin and the bushing.

 B.  
To do the task the steering cylinder rod ends must be disconnected from the steering collar and the steering collar must be removed from the shock strut.

 TASK 32-51-06-206-001
 2.  Steering Collar Wear Examination________________________________
 A.  References
 (1)  
AMM 32-51-06/401, Nose Gear Steering Collar

 (2)  
IPC 32-51-00 Fig. 1, IPC 32-51-06 Fig. 2

 B.  
Access

 (1)  
Location Zone
 715 Nose Landing Gear

 C.  
Procedure (Fig. 601)

 S 026-002
 (1)  
Do this task: "Nose Gear Steering Collar Removal" (AMM 32-51-06/401).

 S 226-003

 (2)  
Do a check of the wear limits of the shock strut, the steering collar bushing, the steering collar, the rod end, the collar pin and the bushings.

 (a)  
Measure the parts interface diameters and compare the measured dimensions to the limit dimensions.

 (b)  
If a part is not within tolerance, repair or replace it, whichever is necessary.

 S 426-004
 (3)  Do this task: "Nose Gear Steering Collar Installation" (AMM 32-51-06/401).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-06
 ALL  ú ú 01 Page 601 ú Oct 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

A
B
1
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 8(36)